Difference between revisions of "Talk:Wireless network configuration"

From ArchWiki
Jump to: navigation, search
m (systemd, rc.conf: re)
(Remove closed topic.)
Line 1: Line 1:
==<s>Encrypting example</s>==
 
It would be good to place a further example for encrypting.
 
 
# /etc/conf.d/wireless
 
wlan_wlan0="wlan0 essid MyEssid"
 
#wlan_wlan0="wlan0 essid MyEssid key 625341627"
 
#wlan_wlan0="wlan0 essid MyEssid key s:masterpassword"
 
 
If you have eth0 as wireless card, you replace wlan0 with eth0
 
wlan_et0="eth0 essid MyEssid key s:masterpassword""
 
-- [[Special:Contributions/87.123.19.20|87.123.19.20]], 27 December 2005
 
:This has to be out-of-date by now. Closing.
 
:-- [[User:Jstjohn|Jstjohn]] ([[User talk:Jstjohn|talk]]) 20:33, 11 November 2012 (UTC)
 
 
 
==Mention modprobe -l==
 
==Mention modprobe -l==
 
Does anybody else besides me think that it would be helpful to mention modprobe -l to get a list of loaded modules/drivers and that ath9k is already included in the kernel at the beginning of ''First steps'' or ''Drivers and Firmware'' section? In my case (I have a Thinkpad x61) I didn't have to install any additional drivers, so I could proceed immediately to Manual setup and everything worked perfectly.
 
Does anybody else besides me think that it would be helpful to mention modprobe -l to get a list of loaded modules/drivers and that ath9k is already included in the kernel at the beginning of ''First steps'' or ''Drivers and Firmware'' section? In my case (I have a Thinkpad x61) I didn't have to install any additional drivers, so I could proceed immediately to Manual setup and everything worked perfectly.
Line 33: Line 19:
 
I now tried again with netcfg and that works like a charm, so it has nothing to do with my hardware. Are there others who are experiencing the same problem?
 
I now tried again with netcfg and that works like a charm, so it has nothing to do with my hardware. Are there others who are experiencing the same problem?
 
<br>-- [[User:Warddr|Warddr]] ([[User talk:Warddr|talk]]) 15:17, 22 August 2012 (UTC)
 
<br>-- [[User:Warddr|Warddr]] ([[User talk:Warddr|talk]]) 15:17, 22 August 2012 (UTC)
 
== <s>systemd, rc.conf</s> ==
 
The section about Management methods needs to be updated with info how to do this on a pure systemd system.<br>
 
-- [[User:JKAbrams|JKAbrams]] 20:51, 02 November 2012
 
 
:I just fixed up [[Wireless_Setup#Management_methods]] a bit. Is this section more useful than it was before? What parts still need work?
 
:-- [[User:Jstjohn|Jstjohn]] ([[User talk:Jstjohn|talk]]) 23:24, 3 November 2012 (UTC)
 
 
::I'm assuming this is resolved. Closing.
 
::-- [[User:Jstjohn|Jstjohn]] ([[User talk:Jstjohn|talk]]) 19:53, 11 November 2012 (UTC)
 
 
Should we add a warning on the top that this article is still not fully systemd converted?<br>
 
-- [[User:t.ask|t.ask]] , 19:40, 13 November 2012 (EST)
 
 
:I just removed a lot of the old initscripts stuff. There's only one section remaining that has not been updated for systemd, and I have already flagged it out of date. I skimmed the article for any other references to initscripts-related content and was unable to find any.
 
:-- [[User:Jstjohn|Jstjohn]] ([[User talk:Jstjohn|talk]]) 22:43, 13 November 2012 (UTC)
 

Revision as of 04:18, 20 November 2012

Mention modprobe -l

Does anybody else besides me think that it would be helpful to mention modprobe -l to get a list of loaded modules/drivers and that ath9k is already included in the kernel at the beginning of First steps or Drivers and Firmware section? In my case (I have a Thinkpad x61) I didn't have to install any additional drivers, so I could proceed immediately to Manual setup and everything worked perfectly.
--Bhobbit 01:03, 7 June 2009 (EDT)

Overall article readability (notes and split)

There is no doubt this article is very rich, but I find it a bit messy overall. At first sight, the newcomer may think managing wireless is a real odyssey, whereas it may be 2 simple steps for most users.

  • More than 50% of the article is dedicated to specific drivers installation. Perhaps it would be worth moving the whole section to a dedicated page, leaving only generic install guidelines here.
  • I've found 21 Note templates. Too much imho, it makes different sections and code lines harder to distinguish, and thus diminishes article's overall readability. Some of them definitely do not deserve a template, they should be written as is.

Still I won't say there is no doubt these 2 changes would make the article really better. So feel free to discuss!

-- Ambrevar (talk) 10:27, 6 July 2012 (UTC)

Auto-connect if dropped or changed location Wicd

I tested this with wicd and this didn't work (with my raspberry pi and an ASUS USB-N10 adaptor). Once the connection was dropped the device didn't even search for other networks (the light at the adaptor didn't blink).

I now tried again with netcfg and that works like a charm, so it has nothing to do with my hardware. Are there others who are experiencing the same problem?
-- Warddr (talk) 15:17, 22 August 2012 (UTC)