Difference between revisions of "Paramano"

From ArchWiki
Jump to: navigation, search
Line 18: Line 18:
 
Most modern computers use the module acpi-cpufreq.  Other options include the p4-clockmod, powernow-k6, powernow-k7, powernow-k8, and speedstep-centrino drivers.  
 
Most modern computers use the module acpi-cpufreq.  Other options include the p4-clockmod, powernow-k6, powernow-k7, powernow-k8, and speedstep-centrino drivers.  
  
To load the driver:
+
To load the driver, modprobe it:
 
  # modprobe acpi-cpufreq
 
  # modprobe acpi-cpufreq
  
To load the driver automatically at start up add the module to /etc/rc.conf
+
To load the driver automatically at start up, add the module to /etc/rc.conf:
 
  # MODULES=( ... acpi-cpufreq ... )
 
  # MODULES=( ... acpi-cpufreq ... )
  

Revision as of 06:40, 5 June 2009


Introduction

Trayfreq (pronounced trayfreek) is a GTK+ application released under GPL that lets you select your CPU's governor or frequency from a tray icon; therefore, trayfreq only depends on GTK+ and anything that can show tray icons.

Installing

Install trayfreq from the AUR. I suggest using one of the AUR Helpers.

System Setup

CPU scaling requires you to have a kernel with the ability already built in or have an appropriate driver module loaded. If the former case represents you, then you do not have to worry. If the latter case represents you, follow the following steps:

Most modern computers use the module acpi-cpufreq. Other options include the p4-clockmod, powernow-k6, powernow-k7, powernow-k8, and speedstep-centrino drivers.

To load the driver, modprobe it:

# modprobe acpi-cpufreq

To load the driver automatically at start up, add the module to /etc/rc.conf:

# MODULES=( ... acpi-cpufreq ... )

CPU Governors Setup

Some CPU governors may not be built into your kernel, and you can add them to /etc/rc.conf to have them automatically load at start up. Again, edit /etc/rc.conf to load the governors' drivers.

# MODULES=( ... cpufreq-conservative cpufreq-powersave cpufreq-userspace cpufreq-ondemand cpufreq-performance ... )

Trayfreq Setup

Now, let's edit the configuration file for trayfreq.

# nano /usr/share/trayfreq/trayfreq.config

Everything will be commented out; uncomment what you want to use. Let's go through the options

  • [events] -- the group events
  • activate=/usr/bin/xterm -- this sets the program to launch when the tray icon is activated (left clicked usually)
  • [governor] -- the group governor
  • default=ondemand -- this sets the default governor to be set when trayfreq starts
  • [frequency] -- the group frequency
  • default=800000 -- this sets the default frequency in hertz to be set when trayfreq starts

Note that, if a default frequency is set, it will override the governor. Setting a frequency sets the maximum frequency and sets the governor to performance.

Sample File:

[events]
activate=/usr/bin/showbatt
[governer]
default=ondemand
#[frequency]
#default=800000


If you want, you can have a configuration file in your home folder, but it cannot set the program to run when the tray icon is activated for security reasons. The file should be ~/.trayfreq.config; if it exists, trayfreq will still look at /usr/share/trayfreq/trayfreq.config for the program to run when the tray icon is activated, but the configuration file in the home folder will override everything else.

Finally

Finally, add trayfreq to a one of the Startup files based on your setup.

Possible Annoyances

  • Because of how trayfreq currently works, if the current governor is to performance, trayfreq will show that it is set to the highest frequency instead of the governor performance. This is because setting it to a specific frequency is setting the maximum frequency to the chosen frequency and changing the governor to performance, and setting the governor to performance is setting the maximum frequency to the maximum available frequency and changing the governor to performance; they're the same!

External Links

trayfreq at u-lite's website