USB 3G Modem
A number of mobile telephone networks around the world offer mobile internet connections over UMTS (or EDGE or GSM) using a portable USB modem device.
pacman -S usbutils
and then examine the output of
which will show the vendor and product IDs of the device. Note that some devices will show two different product IDs at different times as explained below.
Often these devices will have two modes (1) USB flash memory storage (2) USB Modem. The first mode, sometimes known as ZeroCD, is often used to deliver an internet communications program for another operating system and is generally of no interest to Linux users. Additionally some have a slot into which the user can insert an additional flash memory card.
A useful utility for switching these devices into modem mode is usb_modeswitch, available in the AUR. Some devices are now supported in the USB serial kernel module called "option" (after the Option devices, but not limited to just those) and may be used without usb_modeswitch.
A configuration file /etc/usb_modeswitch.conf is supplied with the package. This contains entries for many devices, which are disabled by default. You need to find your device and uncomment the entry.
When a device is switched, its product ID may change to a different value. The vendor ID will remain unchanged. This can be seen in the output of lsusb.
The general procedure is to switch the device into modem mode, make sure the ttyUSB device(s) are recognized by the usbserial kernel module, and then to run wvdial to dial, connect and start pppd.
pacman -S wvdial
The configuration file /etc/wvdial.conf will in general depend on (a) which device you have (b) which mobile network you are connecting to. A single wvdial.conf file can be defined with named sections to be usable with several USB modems and networks, should you need them.
Run (as root)
which will attempt to write /etc/wvdial.conf correctly. You will need to add the user, password and Access Point Name (APN). You can obtain these (i) from your network provider, (ii) from other users via published wvdial.confs, or (iii) by logging the USB tty traffic under another operating system (Sysinternals' Portmon).
A typical /etc/wvdial.conf looks like this:
[Dialer Defaults] Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Modem Type = Analog Modem ISDN = 0 Modem = /dev/ttyUSB2 Baud = 9600 [Dialer thenet] Phone = *99***1# Username = thenetuser Password = thenetpw Stupid Mode = 1 Baud = 460800 Init3 = AT+CGDCONT=1,"IP","apn.thenet.net" [Dialer mypin] Init4 = AT+CPIN=1234
Often there will be several devices (at /dev/ttyUSB0, /dev/ttyUSB1, /dev/ttyUSB2 for example). If in doubt about which to use, try each of them in turn. Once the configuration files are prepared, the internet connection is established with a simple script like this:
usbmodeswitch sleep 2 modprobe usbserial vendor=0xVVVV product=0xMMMM maxSize=4096 sleep 2 wvdial thenet
where VVVV is the hexadecimal vendor ID from lsusb, and MMMM is the hexadecimal product ID when in modem mode, and "thenet" is the name of the section in wvdial.conf which you wish to use. The maxSize option may or may not be necessary. It simplifies matters if you disable the SIM PIN, but if you require it, run "wvdial mypin" before "wvdial thenet".
The final wvdial command should start pppd and the obained IP address should be visible in the terminal output. At that point the internet connection should be live, which can be easily checked with a web browser or by pinging an external IP address.
The Sakis3g, a shell script gone "wild"
Sakis3G is the easiest way (no installation or configuration is required) to have your 3G/UMTS/GRPS connection up and running. It automagically setups your USB or Bluetooth modem, and may even detect operator settings. You should try it when anything else fails! You can install wvdial as well, if it is necessary, although it is not dependent on it. The usb-modeswitch binary is intergrated in the script and is not necessary to be installed separately. Simple instructions to get it run follow below:
pacman -Sy ppp cd /usr/local/bin/ wget 'http://www.sakis3g.org/versions/latest/sakis3g.gz' gunzip sakis3g.gz chmod +x sakis3g ./sakis3g --interactive