USB 3G Modem

From ArchWiki
Revision as of 19:07, 27 November 2009 by Aedit (Talk | contribs) (Related Article)

Jump to: navigation, search

Tango-document-new.pngThis article is a stub.Tango-document-new.png

Notes: please use the first argument of the template to provide more detailed indications. (Discuss in Talk:USB 3G Modem#)

A number of mobile telephone networks around the world offer mobile internet connections over UMTS (or EDGE or GSM) using a portable USB modem device.

Device identification

Install usbutils

pacman -S usbutils

and then examine the output of

$ lsusb

which will show the vendor and product IDs of the device. Note that some devices will show two different product IDs at different times as explained below.

Mode switching

Often these devices will have two modes (1) USB flash memory storage (2) USB Modem. The first mode, sometimes known as ZeroCD, is often used to deliver an internet communications program for another operating system and is generally of no interest to Linux users. Additionally some have a slot into which the user can insert an additional flash memory card.

A useful utility for switching these devices into modem mode is usb_modeswitch, available in the AUR. Some devices are now supported in the USB serial kernel module called "option" (after the Option devices, but not limited to just those) and may be used without usb_modeswitch.

A configuration file /etc/usb_modeswitch.conf is supplied with the package. This contains entries for many devices, which are disabled by default. You need to find your device and uncomment the entry.

When a device is switched, its product ID may change to a different value. The vendor ID will remain unchanged. This can be seen in the output of lsusb.


The general procedure is to switch the device into modem mode, make sure the USBtty device(s) are recognized by the usbserial kernel module, and then to run wvdial to dial, connect and start pppd.

Install wvdial

pacman -S wvdial

The configuration file /etc/wvdial.conf will in general depend on (a) which device you have (b) which mobile network you are connecting to. A single wvdial.conf file can be defined with named sections to be usable with several USB modems and networks, should you need them.

Run (as root)

# wvdialconf

which will attempt to write /etc/wvdial.conf correctly. You will need to add the user, password and Access Point Name (APN). You can obtain these (i) from your network provider, (ii) from other users via published wvdial.confs, or (iii) by logging the USB tty traffic under another operating system.

A typical /etc/wvdial.conf looks like this:

[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
ISDN = 0
Modem = /dev/ttyUSB2
Baud = 9600

[Dialer thenet]
Phone = *99***1#
Username = thenetuser
Password = thenetpw
Stupid Mode = 1
Baud = 460800
Init3 = AT+CGDCONT=1,"IP",""

[Dialer mypin]
Init4 = AT+CPIN=1234

Often there will be several devices (at /dev/ttyUSB0, /dev/ttyUSB1, /dev/ttyUSB2 for example). If in doubt about which to use, try each of them in turn. Once the configuration files are prepared, the internet connection is established with a simple script like this:

sleep 2
modprobe usbserial vendor=0xVVVV product=0xMMMM maxSize=4096
sleep 2
wvdial thenet

where VVVV is the hexadecimal vendor ID from lsusb, and MMMM is the hexadecimal product ID when in modem mode, and "thenet" is the name of the section in wvdial.conf which you wish to use. The maxSize option may or may not be necessary. It simplifies matters if you disable the SIM PIN, but if you require it, run "wvdial mypin" before "wvdial thenet".

The final wvdial command should start pppd and the obained IP address should be visible in the terminal output. At that point the internet connection should be live, which can be easily checked with a web browser or by pinging an external IP address.

Related Articles

Huawei E220
Allow users to dial with wvdial