# USB flash installation media

This page discusses various multi-platform methods on how to create an Arch Linux Installer USB drive (also referred to as "flash drive", "USB stick", "USB key", etc) for booting in BIOS and UEFI systems. The result will be a LiveUSB (LiveCD-like) system that can be used for installing Arch Linux, system maintenance or for recovery purposes, and that, because of the nature of SquashFS, will discard all changes once the computer shuts down.

If you would like to run a full install of Arch Linux from a USB drive (i.e. with persistent settings), see Installing Arch Linux on a USB key. If you would like to use your bootable Arch Linux USB stick as a rescue USB, see Change root.

## BIOS and UEFI bootable USB

### Using dd

Note: This method is recommended due to its simplicity. If it does not work, switch to the alternative method #Using manual formatting below.
Warning: This will irrevocably destroy all data on /dev/sdx. To restore the USB drive as an empty, usable storage device after using the Arch ISO image, the iso9660 filesystem signature needs to be removed by running wipefs --all /dev/sdx as root, before repartitioning and reformating the USB drive.

#### In GNU/Linux

Tip: Find out the name of your USB drive with lsblk. Make sure that it is not mounted.

Run the following command, replacing /dev/sdx with your drive, e.g. /dev/sdb. (Do not append a partition number, so do not use something like /dev/sdb1)

# dd bs=4M if=/path/to/archlinux.iso of=/dev/sdx status=progress && sync

Wait for the command sync to complete before unplugging the USB drive to ensure the data was written completely.

#### In Windows

##### Using Rufus

Rufus is a multi-purpose USB iso writer. Simply select the Arch Linux ISO, the USB drive you want to create the bootable Arch Linux onto and click start.

Since Rufus does not care if the drive is properly formatted or not and provides a GUI it may be the easiest and most robust tool to use.

Note: Be sure to select DD mode or the image will be transferred incorrectly.
##### Using USBwriter

This method does not require any workaround and is as straightforward as dd under Linux. Just download the Arch Linux ISO, and with local administrator rights use the USBwriter utility to write to your USB flash memory.

##### Using win32diskimager

win32diskimager is another graphical USB iso writing tool for Windows. Simply select your iso image and the target USB drive letter (you may have to format it first to assign it a drive letter), and click Write.

##### Using Cygwin

Make sure your Cygwin installation contains the dd package.

Tip: If you do not want to install Cygwin, you can download dd for Windows from here. See the next section for more information.

C:\cygwin\home\John\

Run cygwin as administrator (required for cygwin to access hardware). To write to your USB drive use the following command:

dd if=image.iso of=\\.\x: bs=4M

where image.iso is the path to the iso image file within the cygwin directory and \\.\x: is your USB flash drive where x is the windows designated letter, e.g. \\.\d:.

On Cygwin 6.0, find out the correct partition with:

cat /proc/partitions

and write the ISO image with the information from the output. Example:

Warning: This will irrevocably delete all files on your USB flash drive, so make sure you do not have any important files on the flash drive before doing this.
dd if=image.iso of=/dev/sdb bs=4M
##### dd for Windows

A GPL licensed dd version for Windows is available at http://www.chrysocome.net/dd. The advantage of this over Cygwin is a smaller download. Use it as shown in instructions for Cygwin above.

If your Arch Linux ISO is elsewhere you may need to state the full path, for convenience you may wish to put the Arch Linux ISO into the same folder as the dd executable. The basic format of the command will look like this.

# dd if=archlinux-2017-XX-YY-x86_64.iso od=\\.\x: bs=4M
Note: The Windows drive letters are linked to a partition. To allow selecting the entire disk, dd for Windows provides the od parameter, which is used in the commands above. Note however that this parameter is specific to dd for Windows and cannot be found in other implementations of dd.
Warning: Because the od is used, all partitions on the selected disk will be destroyed. Be absolutely sure that you are directing dd to the correct drive before executing.

Simply replace the various null spots (indicated by an "x") with the correct date and correct drive letter. Here is a complete example.

# dd if=ISOs\archlinux-2017.04.01-x86_64.iso od=\\.\d: bs=4M

Reason: The following note may be invalid, the upstream documentation does not mention anything related to PhysicalDrive. (Discuss in Talk:USB flash installation media#)
Note: Alternatively, replace the drive letter with \\.\PhysicalDriveX, where X is the physical drive number (starts from 0). Example:
# dd if=ISOs\archlinux-2017.04.01-x86_64.iso of=\\.\PhysicalDrive1 bs=4M

You can find out the physical drive number by typing wmic diskdrive list brief at the command prompt or with dd --list

Any Explorer window must be closed or dd will report an error.

#### In macOS

First, you need to identify the USB device. Open /Applications/Utilities/Terminal and list all storage devices with the command:

$diskutil list Your USB device will appear as something like /dev/disk2 (external, physical). Verify that this is the device you want to erase by checking its name and size and then use its identifier for the commands below instead of /dev/diskX. A USB device is normally auto-mounted in macOS, and you have to unmount (not eject) it before block-writing to it with dd. In Terminal, do:$ diskutil unmountDisk /dev/diskX

Now copy the ISO image file to the device. The dd command is similar to its Linux counterpart, but notice the 'r' before 'disk' for raw mode which makes the transfer much faster:

\$ sudo dd if=path/to/arch.iso of=/dev/rdiskX bs=1m

After completion, macOS may complain that "The disk you inserted was not readable by this computer". Select 'Ignore'. The USB device will be bootable.

### Using manual formatting

#### In GNU/Linux

This method is more complicated than writing the image directly with dd, but it does keep the flash drive usable for data storage (that is, the ISO is installed in a specific partition within the already partitioned device without altering other partitions).

Note: Here, we will denote the targeted partition as /dev/sdXn. In any of the following commands, adjust X and n according to your system.
• Make sure that the syslinux package is installed on the system.
• If not done yet, create the partition table and/or partition on the device before continuing. The partition /dev/sdXn must be formatted to FAT32.
• Mount the ISO image, mount the FAT32 filesystem located in the USB flash device, and copy the contents of the ISO image to it. Then unmount the ISO image, but keep the FAT32 partition mounted (this will be used in subsequent steps). Eg:
# mkdir -p /mnt/{iso,usb}
# mount -o loop archlinux-2017.04.01-x86_64.iso /mnt/iso
# mount /dev/sdXn /mnt/usb
# cp -a /mnt/iso/* /mnt/usb
# sync
# umount /mnt/iso
• Note: The following step is not required when using Archboot instead of Archiso.
To boot either a label or an UUID to select the partition to boot from is required. By default the label ARCH_2017XX (with the appropriate release month) is used. Thus, the partition’s label has to be set accordingly, for example using gparted. Alternatively, you can change this behaviour by altering the lines ending by archisolabel=ARCH_2017XX in the file /mnt/usb/arch/boot/syslinux/archiso_sys.cfg (for BIOS boot), and in /mnt/usb/loader/entries/archiso-x86_64.conf (for UEFI boot). To use an UUID instead, replace those portions of lines with archisodevice=/dev/disk/by-uuid/YOUR-UUID. The UUID can be retrieved with blkid -o value -s UUID /dev/sdXn.
Warning: Mismatching labels or wrong UUID prevents booting from the created medium.
• Syslinux is already preinstalled in /mnt/usb/arch/boot/syslinux. Install it completely to that folder by following Syslinux#Manual install. Instructions are reproduced here for convenience.
• Overwrite the existing Syslinux modules (*.c32 files) present in the USB (from the ISO) with the ones from the syslinux package (found in /usr/lib/syslinux/bios). This is necessary to avoid boot failure because of a possible version mismatch.
# cp /usr/lib/syslinux/bios/*.c32 /mnt/usb/arch/boot/syslinux
• Run:
# extlinux --install /mnt/usb/arch/boot/syslinux
• Unmount the partition (umount /mnt/usb).
• Mark the partition as active (or “bootable”).

#### In Windows

Note:
• For manual formatting, do not use any Bootable USB Creator utility for creating the UEFI bootable USB. For manual formatting, do not use dd for Windows to dd the ISO to the USB drive either.
• In the below commands, X: is assumed to be the USB flash drive in Windows.
• Windows uses backward slash \ as path-separator, so the same is used in the below commands.
• All commands should be run in Windows command prompt as administrator.
• > denotes the Windows command prompt.
• Partition and format the USB drive using Rufus USB partitioner. Select partition scheme option as MBR for BIOS and UEFI and File system as FAT32. Uncheck "Create a bootable disk using ISO image" and "Create extended label and icon files" options.
• Change the Volume Label of the USB flash drive X: to match the LABEL mentioned in the archisolabel= part in <ISO>\loader\entries\archiso-x86_64.conf. This step is required for Official ISO (Archiso) but not required for Archboot. This step can be also performed using Rufus, during the prior "partition and format" step.
• Extract the ISO (similar to extracting ZIP archive) to the USB flash drive (using 7-Zip.
• Run the following command (in Windows cmd prompt, as admin):
Note: Use X:\boot\syslinux\ for Archboot iso.
> cd bios\
> for /r %Y in (*.c32) do copy "%Y" "X:\arch\boot\syslinux\" /y
> copy mbr\*.bin X:\arch\boot\syslinux\ /y
• Install Syslinux to the USB by running (use win64\syslinux64.exe for x64 Windows):
Note: Use -d /boot/syslinux for Archboot iso.
> cd bios\
> win32\syslinux.exe -d /arch/boot/syslinux -i -a -m X:
Note:
• The above step installs Syslinux's ldlinux.sys to the VBR of the USB partition, sets the partition as "active/boot" in the MBR partition table and writes the MBR boot code to the 1st 440-byte boot code region of the USB.
• The -d switch expects a path with forward slash path-separator like in *unix systems.

## Other methods for BIOS systems

### In GNU/Linux

#### Using a multiboot USB drive

This allows booting multiple ISOs from a single USB device, including the archiso. Updating an existing USB drive to a more recent ISO is simpler than for most other methods. See Multiboot USB drive.

#### Using GNOME Disk Utility

Linux distributions running GNOME can easily make a live CD through nautilus and gnome-disk-utility. Simply right-click on the .iso file, and select "Open With Disk Image Writer." When GNOME Disk Utility opens, specify the flash drive from the "Destination" drop-down menu and click "Start Restoring."

#### Making a USB-ZIP drive

For some old BIOS systems, only booting from USB-ZIP drives is supported. This method allows you to still boot from a USB-HDD drive.

Warning: This will destroy all information on your USB flash drive!
• Find your usb drive with lsblk.
• Type mkdiskimage -4 /dev/sdx 0 64 32 (replace x with the letter of your drive). This will take a while.

From here continue with the manual formatting method. The partition will be /dev/sdx4 due to the way ZIP drives work.

Note: Do not format the drive as FAT32; keep it as FAT16.

#### Using UNetbootin

UNetbootin can be used on any Linux distribution or Windows to copy your iso to a USB device. However, Unetbootin overwrites syslinux.cfg, so it creates a USB device that does not boot properly. For this reason, Unetbootin is not recommended -- please use dd or one of the other methods discussed in this topic.

Warning: UNetbootin writes over the default syslinux.cfg; this must be restored before the USB device will boot properly.

Edit syslinux.cfg:

sysconfig.cfg
prompt 0
timeout 100

label unetbootindefault
kernel /arch/boot/x86_64/vmlinuz
append initrd=/arch/boot/x86_64/archiso.img archisodevice=/dev/sdx1 ../../

In /dev/sdx1 you must replace x with the first free letter after the last letter in use on the system where you are installing Arch Linux (e.g. if you have two hard drives, use c.). You can make this change during the first phase of boot by pressing Tab when the menu is shown.

### In Windows

#### Win32 Disk Imager

Warning: This will destroy all information on your USB flash drive!

First, download the program from here. Next, extract the archive and run the executable. Now, select the Arch Linux ISO under the Image File section and the USB flash device letter (for example, [D:\]) under the Device section. Finally, click Write when ready.

Note: After installation, you may need to restore the USB flash drive following a process as outlined in #Using dd.

#### USBWriter for Windows

Download the program from http://sourceforge.net/projects/usbwriter/ and run it. Select the arch image file, the target USB stick, and click on the write button. Now you should be able to boot from the usb stick and install Arch Linux from it.

#### The Flashnul way

flashnul is an utility to verify the functionality and maintenance of Flash-Memory (USB-Flash, IDE-Flash, SecureDigital, MMC, MemoryStick, SmartMedia, XD, CompactFlash etc).

From a command prompt, invoke flashnul with -p, and determine which device index is your USB drive, e.g.:

C:\>flashnul -p
Avaible physical drives:
Avaible logical disks:
C:\
D:\
E:\

When you have determined which device is the correct one, you can write the image to your drive, by invoking flashnul with the device index, -L, and the path to your image, e.g:

C:\>flashnul E: -L path\to\arch.iso

As long as you are really sure you want to write the data, type yes, then wait a bit for it to write. If you get an access denied error, close any Explorer windows you have open.

If under Vista or Win7, you should open the console as administrator, or else flashnul will fail to open the stick as a block device and will only be able to write via the drive handle windows provides

Note: Confirmed that you need to use drive letter as opposed to number. flashnul 1rc1, Windows 7 x64.

This article or section is a candidate for merging with Multiboot USB drive#Using Syslinux and memdisk.

Notes: This is the same method, only Syslinux is installed from Windows. Considering that multiboot USB drive can be used to boot an installation media and it is already linked from the Related articles box at the top, maybe this section should be merged there? (Discuss in Talk:USB flash installation media#)

This method uses Syslinux and a Ramdisk (MEMDISK) to load the entire Arch Linux ISO image into RAM. Since this will be running entirely from system memory, you will need to make sure the system you will be installing this on has an adequate amount. A minimum amount of RAM between 500 MB and 1 GB should suffice for a MEMDISK based, Arch Linux install.

For more information on Arch Linux system requirements as well as those for MEMDISK see the Installation guide and here. For reference, here is the preceding forum thread.

Tip: Once the installer has completed loading you can simply remove the USB stick and even use it on a different machine to start the process all over again. Utilizing MEMDISK also allows booting and installing Arch Linux to and from the same USB flash drive.
##### Preparing the USB flash drive

Begin by formatting the USB flash drive as FAT32. Then create the following folders on the newly formatted drive.

• Boot
• Boot/ISOs
• Boot/Settings
##### Copy the needed files to the USB flash drive

Next copy the ISO that you would like to boot to the Boot/ISOs folder. After that, extract from the following files from the latest release of syslinux from here and copy them into the following folders.

• ./memdisk/memdisk to the Settings folder on your USB flash drive.
##### Create the configuration file

After copying the needed files, navigate to the USB flash drive, /boot/Settings and create a syslinux.cfg file.

Warning: On the INITRD line, be sure to use the name of the ISO file that you copied to your ISOs folder!
/Boot/Settings/syslinux.cfg
DEFAULT arch_iso

LABEL arch_iso
LINUX memdisk
INITRD /Boot/ISOs/archlinux-2017.04.01-x86_64.iso
APPEND iso

##### Final steps

Finally, create a *.bat file where syslinux.exe is located and run it ("Run as administrator" if you are on Vista or Windows 7):