Wake-on-LAN, otherwise known as 'wol', is the ability to switch on a computer that is connected to a network (be it the internet or intranet). This article deals with what it is, how it can be used from an Arch Linux computer, and its general uses.
It is important to note that Wake-on-LAN applies to the computers being physically connected (ie, not wireless).
- 1 Does my motherboard support Wake-on-LAN?
- 2 Ensure that Wake-on-LAN is enabled and survives a reboot
- 3 Wake-on-LAN in different situations
- 4 Battery draining problem
- 5 Additional Notes
- 6 Example WOL script
- 7 Resources
Does my motherboard support Wake-on-LAN?
For Wake-on-LAN to work, the target computer motherboard must support this feature. Generally speaking, the Wake-on-LAN (non)ability of the target motherboard will be specified by the hardware manufacturer. Sometimes, this ability is evident by browsing through said motherboard's BIOS and looking for something like 'PCI Power up'. Most modern motherboards should support Wake-on-LAN.
Ensure that Wake-on-LAN is enabled and survives a reboot
A common problem with the Wake-on-LAN in computers running Linux is that the network drivers have Wake-on-LAN switched off by default. To manually switch on the Wake-on-LAN feature on your driver, you will need to install.
First query the driver to see if it's defaulted to 'on' by using ethtool:
# ethtool net0 | grep Wake-on
Supports Wake-on: pg Wake-on: d
To enable the wol feature in the driver, simply run the following
# ethtool -s net0 wol g
This command does not last beyond the next reboot. If using netctl, one can make this setting persistent by adding the following to your netctl profile:
ExecUpPost='/usr/bin/ethtool -s net0 wol g'
- If for some reason, you find that after using the command to switch your network drivers Wake-on-LAN feature on, the computer shuts down normally but then starts again, experiment with combinations of [u/b/m]g
- For some network cards, you may also need the following command:
# echo enabled > /sys/class/net/net0/device/power/wakeup
udev is capable of running any command you desire as soon as a device is visible. We want udev to turn on wake on lan for our device. Put the following in /etc/udev/rules.d/50-wol.rules, replacing N with the number for your interface:
ACTION=="add", SUBSYSTEM=="net", KERNEL=="netN", RUN+="/usr/bin/ethtool -s %k wol g"
This tells udev to run "/usr/bin/ethtool -s netN wol g" as soon as the device netN exists. To turn on wake on lan for all new devices, replace the N with a '*':
ACTION=="add", SUBSYSTEM=="net", KERNEL=="net*", RUN+="/usr/bin/ethtool -s %k wol g"
@reboot /usr/bin/ethtool -s [net-device] wol g
If for some reason udev fails or is not an option, systemd can be used instead as a last resort. (In this editor's experience, systemd is rather intermittent.) To use systemd, do not follow the udev instructions. Instead, create a new service unit file /etc/systemd/system/wol@.service:
[Unit] Description=Wake-on-LAN for %i Requires=network.target After=network.target [Service] ExecStart=/usr/bin/ethtool -s %i wol g Type=oneshot [Install] WantedBy=multi-user.target
Or install AURAUR package from the
Then activate this new service for your network adapter:
# systemctl enable wol@net0
and start it right now
# systemctl start wol@net0
Wake-on-LAN in different situations
The computer that you want to use Wake-on-LAN on may be directly linked to your computer through a network cable, connected to the same router that you are using, or remotely, across the internet.
There are four essential things needed in order to use Wake-on-LAN on a target PC:
- Some kind of Wake-on-LAN software on the host (your) PC
- A connection to the internet or intranet of the target PC
- The MAC address of the target PC
- The internal or external IP of the target PC
- Firstly, install a Wake-on-LAN software. In this article, wol will be used. It can be installed from the [community] repository.
- It is recommended that you read the documentation of wol
man wol wol --help
- wol requires several parameters, the most basic needed:
- But it is good practice to include the IP address or hostname, therefore this syntax should be the minimal used:
# wol -i HOSTNAME_OR_IP MACADDRESS
- The documentation of wol states that:
- Each MAC-ADDRESS is written as x:x:x:x:x:x, where x is a hexadecimal number between 0 and ff which represents one byte of the address, which is in network byte order (big endian).
- To obtain the MACADDRESS of the target computer:
$ ip link
The port, IP or hostname of the target PC will be addressed in the relevant following sections.
Across your intranet/network (no router)
If you are connected directly to another computer through a network cable, or have disabled your router firewall (not a good idea), then using Wake-on-LAN should be very simple.
For two computers connected to each other
For computers connected to a non-firewalled router
wol -i INTERNAL_IP_OF_TARGET_PC MACADDRESS_OF_TARGET_PC
- To find the internal IP:
ip addr | grep 'inet '
- Since you are not firewalled, then there is no need to worry about port redirects.
- If you intend to continue using Wake-on-LAN, it is recommended that you assign your computer's MACADDRESS to a specific IP on your router. Consult your router for details as to how to do this.
Across your intranet/network (router)
The syntax used in this situation:
wol -p PORT_FORWARDED_TO_INTERNAL_IP -i INTERNAL_IP MACADDRESS_OF_TARGET_PC
- When you send the MagicPacket signal to the target computer via a specific port, the signal passes through your router. The router must be instructed to forward any signal heading for that specific port to the internal IP of the target PC.
- It is recommended that for multiple computers connected to one computer, to assign a different port forward to each internal IP
- For port forwarding help, please consult http://portforward.com/ (though this website has some Windows specific content, it has a very large database of router web interfaces)
Across the internet
The syntax needed in this case:
wol -p X -i HOSTNAME_OR_EXTERNAL_IP_OF_TARGET MACADDRESS
- Assuming that you know the external IP of the target machine, and that the router ports on both sides have been forwarding correctly, then this should be exactly as the syntax states.
Usually it is necessary to forward your wol port (typically UDP 9) to the broadcast address on your network, not to a particular IP. Most routers do not allow you to forward to broadcast, however if you can get shell access to your router (through telnet, ssh, serial cable, etc) you can implement this workaround:
ip neighbor add 192.168.1.254 lladdr FF:FF:FF:FF:FF:FF dev net0
(The above command assumes your network is 192.168.1.0/24 and use net0 as network interface). Now, forward UDP port 9 to 192.168.1.254. This has worked for me on a Linksys WRT54G running Tomato, and on the Verizon FIOS ActionTec router.
For notes on how to do it on DD-WRT routers, see this tutorial.
Battery draining problem
Some laptops have battery draining problem after shutdown . This might be caused by enabled Wake-on-LAN. To solve this problem, we can disable it by using ethtool as mentioned above.
# ethtool -s net0 wol d
We can also add this to the /etc/rc.local or /etc/rc.local.shutdown.
- A common problem is that some forget to switch on the Wake-on-LAN feature in their BIOS.
- In some systems the BIOS option "Boot from PCI/PCI-E" needs to be Enabled.
Example WOL script
Here is a script you can use to automate wol to several different machine. Modify as you see fit:
#!/bin/bash # definition of MAC addresses monster=01:12:46:82:ab:4f chronic=00:3a:53:21:bc:30 powerless=1a:32:41:02:29:92 ghost=01:1a:d2:56:6b:e6 while [ "$input1" != quit ]; do echo "Which PC to wake?" echo "p) powerless" echo "m) monster" echo "c) chronic" echo "g) ghost" echo "b) wake monster, wait 40sec, then wake chronic" echo "q) quit and take no action" read input1 if [ $input1 == p ]; then /usr/bin/wol $powerless exit 1 fi if [ $input1 == m ]; then /usr/bin/wol $monster exit 1 fi if [ $input1 == c ]; then /usr/bin/wol $chronic exit 1 fi # this line requires an IP address in /etc/hosts for ghost # and should use wol over the internet provided that port 9 # is forwarded to ghost on ghost's router if [ $input1 == g ]; then /usr/bin/wol -v -h -p 9 ghost $ghost exit 1 fi if [ $input1 == b ]; then /usr/bin/wol $monster echo "monster sent, now waiting for 40sec then waking chronic" sleep 40 /usr/bin/wol $chronic exit 1 fi if [ $input1 == Q ] || [ $input1 == q ]; then echo "later!" exit 1 fi done echo "this is the (quit) end!! c-ya!"