Difference between revisions of "Xilinx ISE WebPACK"

From ArchWiki
Jump to navigation Jump to search
Line 237: Line 237:
p.s. The previous name of this page included the version of arch in order to provide context to the era in which this information was accurate. The removal of this contextual information causes the title to imply that this article is timeless, when in fact it is quite temporal.

Revision as of 00:56, 4 August 2010


Xilinx ISE WebPACK is a complete FPGA/CPLD programmable logic design suite providing:

  • specification of programmable logic, via schematic capture or verilog/VHDL
  • synthesis and fit of specified logic into Xilinx CoolRunner and Spartan devices
  • behavioral and post-fit simulation
  • download of configuration into target device via communications cable
  • support for Linux based development system host


The ISE WebPACK version is downloadable at: http://www.xilinx.com/support/download/index.htm

The download requires registration and licensing agreement, but there is no charge, i.e. it's free as in "Free Beer", but not free as in "Free Speech".

Make sure you select the Linux version.

There are a couple of very helpful HOWTO's at Gentoo:

and this is a Xilinx tip for usb install on Linux: http://www.xilinx.com/support/answers/22648.htm

Some other useful links:

Once ready to download I used, and recommend, the "Download Files Individually" option, once you reach the download page. This downloads the entire installer and installation is performed afterward via:

tar xf webpack_SFD.tar
cd webpack

Xilinx only provides official support for redhat and suse distributions, but I found the initial install of ISE to go smoothly on Arch Linux with kernel-headers

I first installed ISE WebPACK for Linux version 9.2i, but 10.1 was released shortly thereafter. I was pleased to see this updated version was available for linux at the same time as 10.1 for windoze.

After installation, ISE worked fine for design capture, synthesis and simulation. However once I reached the point of trying to download a design to a target device I ran into some trouble. Installing the cable drivers for talking to the target interface cable yielded errors.

I downloaded the standalone driver installation utility from: ftp://ftp.xilinx.com/pub/utilities/fpga/install_drivers.tar.gz

This download yields a file named install_drivers.tar.gz

$ tar xzf install_drivers.tar.gz 

yields a directory named install_drivers/. When I attempted to build the drivers from this file I encountered the following errors:

linux_wrappers.c:48:31: error: linux/ioctl32.h: No such file or directory


linux_wrappers.c:1398: error: ‘struct scatterlist’ has no member named ‘page’

Reading in the Gentoo HOWTO's listed above led me to download the latest Jungo source code, which is the core of the Xilinix linux USB support. I modified the link after reading that the latest Jungo driver was 9.20. I got WinDriver 9.20 from: http://www.jungo.com/st/download/WD920LN.tgz

$ tar xzf WD920LN.tgz 

yields a directory named WinDriver/ Within this directory you'll find:

$ ls WinDriver/redist/ 
configure*      linux_wrappers.c  makefile.in      wdreg*             wdusb_linux.c     windrvr_gcc_v3.a
linux_common.h  linux_wrappers.h  setup_inst_dir*  wdusb_interface.h  windrvr_gcc_v2.a  windrvr_gcc_v3_regparm.a

These are the same core files also found in:

$ ls install_drivers/linux_drivers/windriver32/windrvr/
config.cache    LINUX.2.6.24-ARCH.i386/  makefile         wdusb_interface.h  windrvr_gcc_v3_regparm.a
config.log      linux_common.h           makefile.in      wdusb_linux.c
config.status*  linux_wrappers.c         setup_inst_dir*  windrvr_gcc_v2.a
configure*      linux_wrappers.h         wdreg*           windrvr_gcc_v3.a

So I copied the 9.20 WinDriver files over those found in the install_drivers/ subdirectory:

$ cp -p WinDriver/redist/* install_drivers/linux_drivers/windriver32/windrvr/

This update to the Jungo driver eliminated the error: linux/ioctl32.h: No such file or directory, but the error: ‘struct scatterlist’ has no member named ‘page’ was still persisting.

After research regarding changes to scatterlist.h lead to these discussions: http://kerneltrap.org/Linux/SG_Chaining_Merged

Which describe changes in scatter/gather lists that were implemented in kernel 2.6.23 in Oct 2007.

I implemented the following:

$ cd install_drivers/linux_drivers/windriver32/windrvr/

and apply the patch indicated below to linux_wrappers.c:

> /* added to fix scatterlist without page compile bug -jea 2008-05-09 */
> // #include <linux/scatterlist.h>
<     sgl[0].page = pages[0];
>     sgl[0].page_link = (unsigned long)pages[0];
<             sgl[i].page = pages[i];
>             sgl[i].page_link = (unsigned long)pages[i];
<         void *va = page_address(sgl[i].page) + sgl[i].offset;
>         void *va = page_address((struct page *)sgl[i].page_link) + sgl[i].offset;
<         if (!PageReserved(sgl[i].page))
<             SetPageDirty(sgl[i].page);
<         page_cache_release(sgl[i].page);
>         if (!PageReserved((struct page *)sgl[i].page_link))
>             SetPageDirty((struct page *)sgl[i].page_link);
>         page_cache_release((struct page *)sgl[i].page_link);

or, viewed as a unified patch:

--- before/install_drivers/linux_drivers/windriver32/windrvr/linux_wrappers.c   2008-02-19 09:58:43.000000000  -0800
+++ after/install_drivers/linux_drivers/windriver32/windrvr/linux_wrappers.c    2008-05-15 20:02:23.000000000  -0700
@@ -122,6 +122,9 @@
     static struct pci_dev *pci_root_dev;

+/* added to fix scatterlist without page compile bug -jea 2008-05-09 */
+// #include <linux/scatterlist.h>
 typedef struct
     struct page **pages;
@@ -1788,14 +1791,14 @@ 

     memset (sgl, 0, sizeof(struct scatterlist) * page_count);
     sgl[0].offset = ((unsigned long)buf) & (~PAGE_MASK);
-    sgl[0].page = pages[0];
+    sgl[0].page_link = (unsigned long)pages[0];
     if (page_count > 1)
         sgl[0].length = PAGE_SIZE - sgl[0].offset;
         size -= sgl[0].length;
         for (i=1; i < page_count ; i++, size -= PAGE_SIZE)
-            sgl[i].page = pages[i];
+            sgl[i].page_link = (unsigned long)pages[i];
             sgl[i].length = size < PAGE_SIZE ? size : PAGE_SIZE;
@@ -1820,7 +1823,7 @@
     for (i=0; i<*dma_sglen; i++)
 #if defined(_CONFIG_SWIOTLB)
-        void *va = page_address(sgl[i].page) + sgl[i].offset;
+        void *va = page_address((struct page *)sgl[i].page_link) + sgl[i].offset;
         dma_addr_t dma_addr = virt_to_phys(va); 

         if (dma_addr & ~mask)
@@ -1951,9 +1954,9 @@
 #if defined(_CONFIG_SWIOTLB)
         pci_unmap_single(dev_handle, sg_dma_address(&sgl[i]), sg_dma_len(&sgl[i]), (int)dma_direction);
-        if (!PageReserved(sgl[i].page))
-            SetPageDirty(sgl[i].page);
-        page_cache_release(sgl[i].page);
+        if (!PageReserved((struct page *)sgl[i].page_link))
+            SetPageDirty((struct page *)sgl[i].page_link);
+        page_cache_release((struct page *)sgl[i].page_link);
 #elif defined(LINUX_24)

This corrected the compile errors in the Jungo USB driver and produced the windrvr6.ko kernel module. However there was still a nagging error in the compilation of install_drivers/linux_drivers/xpc4drvr2_6/xpc4drvr/

scripts/Makefile.build:46: *** CFLAGS was changed in "/home/johnea/src/before/install_drivers/linux_drivers/xpc4drvr2_6/xpc4drvr/Makefile". Fix it to use EXTRA_CFLAGS.  Stop.
make[1]: *** [_module_/home/johnea/src/before/install_drivers/linux_drivers/xpc4drvr2_6/xpc4drvr] Error 2
make[1]: Leaving directory `/usr/src/linux-2.6.24-ARCH'
make: *** [default] Error 2

which was corrected by the following brutal hack to the Makefile:

diff before/install_drivers/linux_drivers/xpc4drvr2_6/xpc4drvr/Makefile  \ 

< ifeq ($(GET_USER_SIZE_SYM),0)
> #ifeq ($(GET_USER_SIZE_SYM),)
< endif
> #endif

This corrected all compilation errors, but the xpc4drvr.ko still yielded the following error in /var/log/everything.log whenever it was attempted to be loaded:

xpc4drvr: Unknown symbol get_user_size

However this did allow compilation of the entire driver tree and the install script was able to successfully install the drivers via:

cd install_drivers/

There is also a udev rule entry that will make the driver accessible to all users after each reboot. (Which I haven't yet applied)

So after this brief modification, I am able to successfully run ISE on Arch Linux (kernel26 2.6.24) with full USB cable support.

There is a GPL'd libusb based driver mentioned in the Gentoo HOWTO: http://www.rmdir.de/~michael/xilinx/ that I was particularly interested in using. However while the source built without error, I continued to receive runtime errors when attempting to run it in ISE.

I never attempted to use the Xup driver.

There were quite a few pertinent facts along the way that I'm failing to capture here. Such as the fact that I discovered the same directory:


in the base install of the entire ISE package under:


I would expect that this procedure could be applied directly to that without the additional step of downloading the install_drivers.tar.gz but I haven't tried this.

Additionally, as a housekeeping note, the commands above expect all files to be downloaded and untared in the same working directory.

All in all this is the crux of what was necessary for me to get the USB support running on Arch.

Sorry for the somewhat fragmented description, but hopefully this allows others to get this great tool for linux users running on the post 2.6.23 kernels.

Happy Hardware Hacking!!!

Update 2010-08-02

Comments in the forum thread announcing this wiki entry make reference to the page:


This is the upstream source for non-proprietary Xilinx USB drivers using libusb. This is now the Xilinx recommended linux usb interface and is shipped with new versions of Xilinx ISE WebPack.

Per a note on the rmdir.de website, newer versions of udev no longer support the older syntax of the /etc/udev/rules.d/xusbdfwu.rules file:

* 2010-03-15: If you are using newer udev-versions (like the version included in Debian Squeeze and Ubuntu 9.10), then the file /etc/udev/rules.d/xusbdfwu.rules is incompatible with this udev version. The effect of this is that the cable-firmware gets never loaded and the cable led never lights up.

To fix this, run the following command as root:
sed -i -e 's/TEMPNODE/tempnode/' -e 's/SYSFS/ATTRS/g' -e 's/BUS/SUBSYSTEMS/' /etc/udev/rules.d/xusbdfwu.rules
You may have to reboot for this change to take effect.

I didn't require a reboot for this patch to take affect while running:

[root@vhost pcusb]# pacman -Q udev
udev 151-3
[root@vhost pcusb]# pacman -Q kernel26

In both the x86_64 host and the i686 chroot.