USB MIDI keyboards
This how-to assumes that you are using ALSA and that your sound card is set up so you can listen to music. Known to work using this how-to is the Evolution MK-631 USB midi keyboard with SB Live! Value card. Execute these instructions as an unprivileged user unless otherwise noted.
Install the package.
aseqdump. It should output something like:
Waiting for data at port 128:0. Press Ctrl+C to end. Source_ Event_________________ Ch _Data__
Not much will show up there, so press Ctrl+C to quit the program.
Plugging the keyboard
Now plug the keyboard in and turn it on. The keyboard should power up. Output of
lsusb should contain:
Bus 002 Device 002: ID 0a4d:00a0 Evolution Electronics, Ltd
lsmod | grep usb should contain the following modules:
usb_midi 25348 0 snd_usb_audio 70592 0 snd_usb_lib 16640 1 snd_usb_audio
aconnect -i to list all MIDI input ports. The output should contain:
client 72: 'MK-361 USB MIDI keyboard' [type=kernel] 0 'MK-361 USB MIDI keyboard MIDI 1'
The client number is probably going to be different though. Take note of it.
aseqdump -p ## where you should replace
## with the client number of your keyboard. You should see:
72:0 Active Sensing
popping out all the time. Pressing a key should produce:
72:0 Note on 0 65 94 72:0 Note on 0 65 0
Various other events (turning control knobs, changing channels, etc.) should register in the list. This is a handy way of ensuring that your keyboard is running properly.
To send MIDI events back to the keyboard or another MIDI output device, you can use run
aplaymidi -p ## midifile.mid and specify a MIDI file.
arecordmidi -l to list the available input devices, and determine the
port_number for the desired device.
Then, execute the following to start recording:
arecordmidi -p <port_number> <output_file>
To stop recording, simply
kill the process.
man arecordmidi provides details about additional options available with this tool.
To hear a sound when you push a button on your keyboard, you need a synthesizer that converts the MIDI signal into audio.
Some soundcards have a built-in hardware synthesizer, but these are not common in modern sound cards, especially not in onboard sound cards. An easier option is a software synthesizer, which is just a program which you can load with you own instrument samples.
aconnect -o to list all MIDI output ports. It depends a lot on your sound card. On SB Live! Value, you get the following output:
client 64: 'EMU10K1 MPU-401 (UART)' [type=kernel] 0 'EMU10K1 MPU-401 (UART)' client 65: 'Emu10k1 WaveTable' [type=kernel] 0 'Emu10k1 Port 0 ' 1 'Emu10k1 Port 1 ' 2 'Emu10k1 Port 2 ' 3 'Emu10k1 Port 3 '
Here client 65 is the actual MIDI synthesizer. Assuming the soundcard is set up properly, you should be able to route the output of the keyboard to the MIDI synthesizer. Assuming out is the output client number (65 in our example) and in is the input client number (72 in our example), type
aconnect in out. Now you can play your keyboard via the MIDI output of your sound card.
- Install .
- Start QSynth and go to Setup, where you need to load soundfont in SF2 format. You can get free SoundFonts from http://soundfonts.narod.ru/ (in Russian). When QSynth asks you to restart the engine after loading the SoundFont, do so. AUR, or from
aconnect -oto list all MIDI output ports. Find the one that contains
FLUID Synthand note the client number.
aconnect -ito list all MIDI input ports. Note the Keyboard client number.
- Assuming out is the output client number and in is the input client number (72 in our example), type
aconnect in out. Now you can play your keyboard and QSynth should produce sounds.
aconnect in outeach time you restart Qsynth or change the instrument/SoundFont.
Qsynth using JACK
- We need to install JACK, ,
- Launch qjackctl and check the settings:
Server Path: jackd Driver: alsa Realtime=enable; Priority:0 Frames/Period:512 Soft Mode=enable; Periods/Buffer:2 Rest of parameters=disable(by default) Dither: None Audio: Duplex
- Start jackd using qjackctl (the Play button)
- Connect your USB keyboard
- Start QSynth and go to Setup, where you need to load soundfont in SF2 format. You can get free SoundFonts from http://soundfonts.narod.ru/ (in Russian). When QSynth asks you to restart the engine after loading the SoundFont, do so.
- Go to qjackctl, click Connect and choose the ALSA tab. On the left side you will see connected MIDI keyboard, on the left side - QSynth. Choose MIDI keyboard and QSynth, and click Connect.