Network configuration

Related articles

• Jumbo frames
• Firewalls
• Wireless network configuration
• Network bridge
• List of applications/Internet#Network managers

This page explains how to set up a wired connection to a network. If you need to set up wireless networking see the Wireless network configuration page.

Check the connection

The basic installation procedure typically has a functional network configuration. Use ping(8) to check the connection:

$ ping www.google.com

PING www.l.google.com (74.125.132.105) 56(84) bytes of data.
64 bytes from wb-in-f105.1e100.net (74.125.132.105): icmp_req=1 ttl=50 time=17.0 ms
...

If the ping is successful (you see 64 bytes messages as above), then the network is configured. Press Control-C to stop the ping.

If the ping failed with an Unknown hosts error, it means that your machine was unable to resolve this domain name. It may be related to your service provider or your router/gateway. Try pinging a static IP address to prove that your machine has access to the Internet:

$ ping 8.8.8.8

PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_req=1 ttl=53 time=52.9 ms
...

If you are able to ping 8.8.8.8 but not www.google.com, check your DNS configuration. See resolv.conf for details. The hosts line in /etc/nsswitch.conf is another place you can check.

If not, check for cable issues before diagnosing further.

Note:

• If you receive an error like ping: icmp open socket: Operation not permitted when executing ping, try to re-install the iputils package.
• The -c num option can be used to make exactly num pings, otherwise it pings infinitely and has to be terminated manually. See ping(8) for more information.
• 8.8.8.8 is a static address that is easy to remember. It is the address of Google's primary DNS server, therefore it can be considered reliable, and is generally not blocked by content filtering systems and proxies.

Set the hostname

A hostname is a unique name created to identify a machine on a network, configured in /etc/hostname—see hostname(5) and hostname(7) for details. The file can contain the system's domain name, if any. To set the hostname, edit /etc/hostname to include a single line with myhostname:

/etc/hostname

myhostname

Tip: For advice on choosing a hostname, see RFC 1178.

Alternatively, using hostnamectl(1):

# hostnamectl set-hostname myhostname

To temporarily set the hostname (until reboot), use hostname(1) from inetutils:

# hostname myhostname

To set the "pretty" hostname and other machine metadata, see machine-info(5) § https://www.freedesktop.org/software/systemd/man/machine-info.html.

Local network hostname resolution

The pre-requisite is to #Set the hostname, after which hostname resolution works on the local system itself:

$ ping myhostname

PING myhostname (192.168.1.2) 56(84) bytes of data.
64 bytes from myhostname (192.168.1.2): icmp_seq=1 ttl=64 time=0.043 ms

To allow other machines to address the host by name, it is necessary to either:

• Configure the hosts(5) file, or
• Enable a service which resolves the hostname.

Note: systemd provides hostname resolution via the myhostname nss module, enabled by default in /etc/nsswitch.conf. However, clients may still rely on /etc/hosts, see [1] [2] for examples.

To configure the hosts file, add the following line to /etc/hosts:

127.0.1.1	myhostname.localdomain	myhostname

As a result the system resolves to both entries:

$ getent hosts

127.0.0.1       localhost
127.0.1.1       myhostname.localdomain myhostname

For a system with a permanent IP address, that permanent IP address should be used instead of 127.0.1.1.

Note: Another option is to set up a full DNS server such as BIND or Unbound, but that is overkill and too complex for most systems. For small networks and dynamic flexibility with hosts joining and leaving the network zero-configuration networking services may be more applicable:

• Samba provides hostname resolution via Microsoft's NetBIOS. It only requires installation of samba and enabling of the nmbd.service service. Computers running Windows, macOS, or Linux with nmbd running, will be able to find your machine.
• Avahi provides hostname resolution via zeroconf, also known as Avahi or Bonjour. It requires slightly more complex configuration than Samba: see Avahi#Hostname resolution for details. Computers running macOS, or Linux with an Avahi daemon running, will be able to find your machine. Windows does not have an built-in Avahi client or daemon.

Device driver

Check the status

udev should detect your network interface card (see Wikipedia:Network interface controller) and automatically load the necessary module at start up. Check the "Ethernet controller" entry (or similar) from the lspci -v output. It should tell you which kernel module contains the driver for your network device. For example:

$ lspci -v

02:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0)
 	...
 	Kernel driver in use: atl1
 	Kernel modules: atl1

Next, check that the driver was loaded via dmesg | grep module_name. For example:

$ dmesg | grep atl1

...
atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex

Skip the next section if the driver was loaded successfully. Otherwise, you will need to know which module is needed for your particular model.

Load the module

Search in the Internet for the right module/driver for the chipset. Some common modules are 8139too for cards with a Realtek chipset, or sis900 for cards with a SiS chipset. Once you know which module to use, try to load it manually. If you get an error saying that the module was not found, it's possible that the driver is not included in Arch kernel. You may search the AUR for the module name.

If udev is not detecting and loading the proper module automatically during bootup, see Kernel modules#Automatic module handling.

Network management

Device names

For computers with multiple NICs, it is important to have fixed device names. Many configuration problems are caused by interface name changing.

udev is responsible for which device gets which name. Systemd uses Predictable Network Interface Names, which automatically assigns static names to network devices. Interfaces are now prefixed with en (wired/Ethernet), wl (wireless/WLAN), or ww (WWAN) followed by an automatically generated identifier, creating an entry such as enp0s25.

Tip: This behavior may be disabled by adding net.ifnames=0 to the kernel parameters.

Note: When changing the interface naming scheme, do not forget to update all network-related configuration files and custom systemd unit files to reflect the change. Specifically, if you have netctl static profiles enabled, run netctl reenable profile to update the generated service file.

Get current device names

Both wired and wireless device names can be found via:

$ ls /sys/class/net

or

$ ip link

Note that lo is the W:Loop_device and not used in making network connections.

Wireless device names can also be retrieved using iw dev. See Wireless network configuration#Getting some useful information for details.

Tip: To change the device names, see #Change device name and #Revert to traditional device names.

Enabling and disabling network interfaces

You can activate a network interface using:

# ip link set interface up

To deactivate it do:

# ip link set interface down

To check the result for the interface eth0:

$ ip link show dev eth0

2: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master br0 state UP mode DEFAULT qlen 1000
...

Note: If your default route is through interface eth0, taking it down will also remove the route, and bringing it back up will not automatically reestablish the default route. See #Manual assignment for reestablishing it.

Configure a dynamic IP address

See #Network managers for a list of options in setting a dynamic IP address.

Alternatively, install the dhclient package, which is the Internet Systems Consortium DHCP client. Then, enable the dhclient@interface.service, where interface is a wired device name. See dhclient(8) and dhclient.conf(5) for details.

Configure a static IP address

A static IP address can be configured with most standard Arch Linux #Network managers. Independent of the tool you choose, you will probably need to be prepared with the following information:

• Static IP address
• Subnet mask, or possibly its CIDR notation, for example /24 is the CIDR notation of 255.255.255.0 netmask.
• Broadcast address
• Gateway's IP address
• Name server (DNS) IP addresses. See also resolv.conf.

If you are running a private network, it is safe to use IP addresses in 192.168.*.* for your IP addresses, with a subnet mask of 255.255.255.0 and a broadcast address of 192.168.*.255. The gateway is usually 192.168.*.1 or 192.168.*.254.

Warning:

• Make sure manually assigned IP addresses do not conflict with DHCP assigned ones. See this forum thread.
• If you share your Internet connection from a Windows machine without a router, be sure to use static IP addresses on both computers to avoid LAN problems.

Tip: Addresses can be calculated with the ipcalc package; see #Calculating addresses.

Manually setting a static IP address

It is possible to manually set up a static IP using only the iproute2 package. This is a good way to test connection settings since the connection made using this method will not persist across reboots. First enable the network interface:

# ip link set interface up

Assign a static IP address in the console:

# ip addr add IP_address/subnet_mask broadcast broadcast_address dev interface

Then add your gateway IP address:

# ip route add default via default_gateway

For example:

# ip link set eth0 up
# ip addr add 192.168.1.2/24 broadcast 192.168.1.255 dev eth0
# ip route add default via 192.168.1.1

Tip: If you get the message RTNETLINK answers: Network is unreachable, try to break up the route creation in the following two parts:

# ip route add 192.168.1.1 dev eth0
# ip route add default via 192.168.1.1 dev eth0

To undo these steps (e.g. before switching to a dynamic IP), first remove any assigned IP address:

# ip addr flush dev interface

Then remove any assigned gateway:

# ip route flush dev interface

And finally disable the interface:

# ip link set interface down

For more options, see the ip(8). These commands can be automated using scripts and systemd units.

Calculating addresses

You can use ipcalc provided by the ipcalc package to calculate IP broadcast, network, netmask, and host ranges for more advanced configurations. An example is using Ethernet over Firewire to connect a Windows machine to Linux. To improve security and organization, both machines have their own network with the netmask and broadcast configured accordingly.

Finding out the respective netmask and broadcast addresses is done with ipcalc, by specifying the IP of the Linux NIC 10.66.66.1 and the number of hosts (here two):

$ ipcalc -nb 10.66.66.1 -s 1

Address:   10.66.66.1

Netmask:   255.255.255.252 = 30
Network:   10.66.66.0/30
HostMin:   10.66.66.1
HostMax:   10.66.66.2
Broadcast: 10.66.66.3
Hosts/Net: 2                     Class A, Private Internet

Network managers

There are many solutions to choose from, but remember that all of them are mutually exclusive; you should not run two daemons simultaneously. The following table compares the different connection managers. Automatically handles wired connection means that there is at least one option for the user to simply start the daemon without creating a configuration file.

Connection manager	Automatically handles wired connection	Official GUI	Console tools	Systemd units
Connman	Yes	No	connmanctl	connman.service
dhcpcd	Yes	No	dhcpcd	dhcpcd.service, dhcpcd@interface.service
netctl	Yes	No	netctl	netctl-ifplugd@interface.service
NetworkManager	Yes	Yes	nmcli,nmtui	NetworkManager.service
systemd-networkd	No	No		systemd-networkd.service, systemd-resolved.service
Wicd	Yes	Yes	wicd-curses	wicd.service

See List of applications#Network managers.

Tips and tricks

Change device name

You can change the device name by defining the name manually with an udev-rule. For example:

/etc/udev/rules.d/10-network.rules

SUBSYSTEM=="net", ACTION=="add", ATTR{address}=="aa:bb:cc:dd:ee:ff", NAME="net1"
SUBSYSTEM=="net", ACTION=="add", ATTR{address}=="ff:ee:dd:cc:bb:aa", NAME="net0"

These rules will be applied automatically at boot.

A couple of things to note:

• To get the MAC address of each card, use this command: cat /sys/class/net/device_name/address
• Make sure to use the lower-case hex values in your udev rules. It doesn't like upper-case.

If the network card has a dynamic MAC, you can use DEVPATH, for example:

/etc/udev/rules.d/10-network.rules

SUBSYSTEM=="net", DEVPATH=="/devices/platform/wemac.*", NAME="int"
SUBSYSTEM=="net", DEVPATH=="/devices/pci*/*1c.0/*/net/*", NAME="en"

The device path should match both the new and old device name, since the rule may be executed more than once on bootup. For example, in the second rule, "/devices/pci*/*1c.0/*/net/enp*" would be wrong since it will stop matching once the name is changed to en. Only the system-default rule will fire the second time around, causing the name to be changed back to e.g. enp1s0.

To test your rules, they can be triggered directly from userspace, e.g. with udevadm --debug test /sys/DEVPATH. Remember to first take down the interface you are trying to rename (e.g. ip link set enp1s0 down).

Note: When choosing the static names it should be avoided to use names in the format of "ethX" and "wlanX", because this may lead to race conditions between the kernel and udev during boot. Instead, it is better to use interface names that are not used by the kernel as default, e.g.: net0, net1, wifi0, wifi1. For further details please see the systemd documentation.

Revert to traditional device names

If you would prefer to retain traditional interface names such as eth0, Predictable Network Interface Names can be disabled by masking the udev rule:

 # ln -s /dev/null /etc/udev/rules.d/80-net-setup-link.rules

Set device MTU and queue length

You can change the device MTU and queue length by defining manually with an udev-rule. For example:

/etc/udev/rules.d/10-network.rules

ACTION=="add", SUBSYSTEM=="net", KERNEL=="wl*", ATTR{mtu}="1480", ATTR{tx_queue_len}="2000"

ifplugd for laptops

Tip: dhcpcd provides the same feature out of the box.

ifplugd is a daemon which will automatically configure your Ethernet device when a cable is plugged in and automatically unconfigure it if the cable is pulled. This is useful on laptops with onboard network adapters, since it will only configure the interface when a cable is really connected. Another use is when you just need to restart the network but do not want to restart the computer or do it from the shell.

By default it is configured to work for the eth0 device. This and other settings like delays can be configured in /etc/ifplugd/ifplugd.conf.

Note: netctl package includes netctl-ifplugd@.service, otherwise you can use ifplugd@.service from ifplugd package. For example, enable ifplugd@eth0.service.

Bonding or LAG

See netctl#Bonding or Wireless bonding.

IP address aliasing

IP aliasing is the process of adding more than one IP address to a network interface. With this, one node on a network can have multiple connections to a network, each serving a different purpose. Typical uses are virtual hosting of Web and FTP servers, or reorganizing servers without having to update any other machines (this is especially useful for nameservers).

Example

To manually set an alias, for some NIC, use iproute2 to execute

# ip addr add 192.168.2.101/24 dev eth0 label eth0:1

To remove a given alias execute

# ip addr del 192.168.2.101/24 dev eth0:1

Packets destined for a subnet will use the primary alias by default. If the destination IP is within a subnet of a secondary alias, then the source IP is set respectively. Consider the case where there is more than one NIC, the default routes can be listed with ip route.

Change MAC/hardware address

See MAC address spoofing.

Internet sharing

See Internet sharing.

Router configuration

See Router.

Promiscuous mode

Toggling promiscuous mode will make a (wireless) NIC forward all traffic it receives to the OS for further processing. This is opposite to "normal mode" where a NIC will drop frames it is not intended to receive. It is most often used for advanced network troubleshooting and packet sniffing.

/etc/systemd/system/promiscuous@.service

[Unit]
Description=Set %i interface in promiscuous mode
After=network.target

[Service]
Type=oneshot
ExecStart=/usr/bin/ip link set dev %i promisc on
RemainAfterExit=yes

[Install]
WantedBy=multi-user.target

If you want to enable promiscuous mode on interface eth0 run enable promiscuous@eth0.service.

Troubleshooting

Swapping computers on the cable modem

Some cable ISPs (videotron for example) have the cable modem configured to recognize only one client PC, by the MAC address of its network interface. Once the cable modem has learned the MAC address of the first PC or equipment that talks to it, it will not respond to another MAC address in any way. Thus if you swap one PC for another (or for a router), the new PC (or router) will not work with the cable modem, because the new PC (or router) has a MAC address different from the old one. To reset the cable modem so that it will recognise the new PC, you must power the cable modem off and on again. Once the cable modem has rebooted and gone fully online again (indicator lights settled down), reboot the newly connected PC so that it makes a DHCP request, or manually make it request a new DHCP lease.

If this method does not work, you will need to clone the MAC address of the original machine. See also #Change MAC/hardware address.

The TCP window scaling problem

TCP packets contain a "window" value in their headers indicating how much data the other host may send in return. This value is represented with only 16 bits, hence the window size is at most 64Kb. TCP packets are cached for a while (they have to be reordered), and as memory is (or used to be) limited, one host could easily run out of it.

Back in 1992, as more and more memory became available, RFC 1323 was written to improve the situation: Window Scaling. The "window" value, provided in all packets, will be modified by a Scale Factor defined once, at the very beginning of the connection. That 8-bit Scale Factor allows the Window to be up to 32 times higher than the initial 64Kb.

It appears that some broken routers and firewalls on the Internet are rewriting the Scale Factor to 0 which causes misunderstandings between hosts. The Linux kernel 2.6.17 introduced a new calculation scheme generating higher Scale Factors, virtually making the aftermaths of the broken routers and firewalls more visible.

The resulting connection is at best very slow or broken.

How to diagnose the problem

First of all, let's make it clear: this problem is odd. In some cases, you will not be able to use TCP connections (HTTP, FTP, ...) at all and in others, you will be able to communicate with some hosts (very few).

When you have this problem, the dmesg's output is OK, logs are clean and ip addr will report normal status... and actually everything appears normal.

If you cannot browse any website, but you can ping some random hosts, chances are great that you're experiencing this problem: ping uses ICMP and is not affected by TCP problems.

You can try to use Wireshark. You might see successful UDP and ICMP communications but unsuccessful TCP communications (only to foreign hosts).

Ways of fixing it

Bad

To fix it the bad way, you can change the tcp_rmem value, on which Scale Factor calculation is based. Although it should work for most hosts, it is not guaranteed, especially for very distant ones.

# echo "4096 87380 174760" > /proc/sys/net/ipv4/tcp_rmem

Good

Simply disable Window Scaling. Since Window Scaling is a nice TCP feature, it may be uncomfortable to disable it, especially if you cannot fix the broken router. There are several ways to disable Window Scaling, and it seems that the most bulletproof way (which will work with most kernels) is to add the following line to /etc/sysctl.d/99-disable_window_scaling.conf (see also sysctl):

net.ipv4.tcp_window_scaling = 0

Best

This problem is caused by broken routers/firewalls, so let's change them. Some users have reported that the broken router was their very own DSL router.

More about it

This section is based on the LWN article TCP window scaling and broken routers and a Kernel Trap article: Window Scaling on the Internet.

There are also several relevant threads on the LKML.

Realtek no link / WOL problem

Users with Realtek 8168 8169 8101 8111(C) based NICs (cards / and on-board) may notice a problem where the NIC seems to be disabled on boot and has no Link light. This can usually be found on a dual boot system where Windows is also installed. It seems that using the offical Realtek drivers (dated anything after May 2007) under Windows is the cause. These newer drivers disable the Wake-On-LAN feature by disabling the NIC at Windows shutdown time, where it will remain disabled until the next time Windows boots. You will be able to notice if this problem is affecting you if the Link light remains off until Windows boots up; during Windows shutdown the Link light will switch off. Normal operation should be that the link light is always on as long as the system is on, even during POST. This problem will also affect other operating systems without newer drivers (eg. Live CDs). Here are a few fixes for this problem.

Enable the NIC directly in Linux

Follow #Enabling and disabling network interfaces to enable the interface.

Rollback/change Windows driver

You can roll back your Windows NIC driver to the Microsoft provided one (if available), or roll back/install an official Realtek driver pre-dating May 2007 (may be on the CD that came with your hardware).

Enable WOL in Windows driver

Probably the best and the fastest fix is to change this setting in the Windows driver. This way it should be fixed system-wide and not only under Arch (eg. live CDs, other operating systems). In Windows, under Device Manager, find your Realtek network adapter and double-click it. Under the "Advanced" tab, change "Wake-on-LAN after shutdown" to "Enable".

In Windows XP (example):

Right click my computer and choose "Properties"
--> "Hardware" tab
  --> Device Manager
    --> Network Adapters
      --> "double click" Realtek ...
        --> Advanced tab
          --> Wake-On-Lan After Shutdown
            --> Enable

Note: Newer Realtek Windows drivers (tested with Realtek 8111/8169 LAN Driver v5.708.1030.2008, dated 2009/01/22, available from GIGABYTE) may refer to this option slightly differently, like Shutdown Wake-On-LAN --> Enable. It seems that switching it to Disable has no effect (you will notice the Link light still turns off upon Windows shutdown). One rather dirty workaround is to boot to Windows and just reset the system (perform an ungraceful restart/shutdown) thus not giving the Windows driver a chance to disable LAN. The Link light will remain on and the LAN adapter will remain accessible after POST - that is until you boot back to Windows and shut it down properly again.

Newer Realtek Linux driver

Any newer driver for these Realtek cards can be found for Linux on the realtek site (untested but believed to also solve the problem).

Enable LAN Boot ROM in BIOS/CMOS

It appears that setting Integrated Peripherals --> Onboard LAN Boot ROM --> Enabled in BIOS/CMOS reactivates the Realtek LAN chip on system boot-up, despite the Windows driver disabling it on OS shutdown.

Note: This was tested several times on a GIGABYTE GA-G31M-ES2L motherboard, BIOS version F8 released on 2009/02/05.

No interface with Atheros chipsets

Users of some Atheros ethernet chips are reporting it does not work out-of-the-box (with installation media of February 2014). The working solution for this is to install backports-patched^AUR.

Broadcom BCM57780

This Broadcom chipset sometimes does not behave well unless you specify the order of the modules to be loaded. The modules are broadcom and tg3, the former needing to be loaded first.

These steps should help if your computer has this chipset:

• Find your NIC in lspci output:

$ lspci | grep Ethernet

02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01)

• If your wired networking is not functioning in some way or another, try unplugging your cable then doing the following:

# modprobe -r tg3
# modprobe broadcom
# modprobe tg3

• Plug your network cable in. If this solves your problems you can make this permanent by adding broadcom and tg3 (in this order) to the MODULES array in /etc/mkinitcpio.conf:

MODULES=".. broadcom tg3 .."

• Rebuild the initramfs:

# mkinitcpio -p linux

• Alternatively, you can create an /etc/modprobe.d/broadcom.conf:

softdep tg3 pre: broadcom

Note: These methods may work for other chipsets, such as BCM57760.

Realtek RTL8111/8168B

# lspci | grep Ethernet

03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)

The adapter should be recognized by the r8169 module. However, with some chip revisions the connection may go off and on all the time. The alternative r8168 should be used for a reliable connection in this case. Blacklist r8169, if r8168 is not automatically loaded by udev, see Kernel modules#Automatic module handling.

Another fault in the drivers for some revisions of this adapter is poor IPv6 support. IPv6#Disable functionality can be helpful if you encounter issues such as hanging webpages and slow speeds.

Gigabyte Motherboard with Realtek 8111/8168/8411

With motherboards such as the Gigabyte GA-990FXA-UD3, booting with IOMMU off (which can be the default) will cause the network interface to be unreliable, often failing to connect or connecting but allowing no throughput. This will apply not only to the onboard NIC, but any other pci-NIC you put in the box because the IOMMU setting affects the entire network interface on the board. Enabling IOMMU and booting with the install media will throw AMD I-10/xhci page faults for a second, but then boot normally, resulting in a fully functional onboard NIC (even with the r8169 module).

When configuring the boot process for your installation, add iommu=soft as a kernel parameter to eliminate the error messages on boot and restore USB3.0 functionality.

See also

• Debian Reference: Network setup
• RHEL7: Networking Guide