CUPS (简体中文)/Printer sharing (简体中文)
您的客户端需要支持Avahi主机名解析，否则客户端可能报错称“找不到打印机”("Unable to locate printer")。详情请参考avahi#Hostname resolution。
点击页面上方的Administration按钮, 在Printer下选择“add printer”，将会自动检测已连接的打印机。如果打印机无法被检测，请尝试将打印机重启后重新检测。
打印机设置好之后，将Server下的"Share printers connected to this system"改为选中状态，然后点击下方的change settings保存修改。这时打印服务器将自动重启。
选择"Edit Configuration File"即可直接修改配置文件
<Location /> Order allow,deny Allow localhost Allow 192.168.0.* </Location>
此外我们需要保证服务器端正在监听客户端所在的IP地址。在"# Listen <serverip>:631"之后添加如下内容（注意：“Listen”后面为服务器的IP地址，而非客户端IP地址）：
为了“让打印机在局域网中可见”("Show shared printers on the local network")，请添加如下内容以保证Browsing指令可以使用：
在CUPS 1.6及其之后的版本中, 客户端默认采用IPP 2.0。如果服务器端的CUPS版本<=1.5/IPP版本<= 1.1，由于客户端不会自动使用较早版本的通信协议，客户端将无法与服务器端交流。一个可行的方法是在
Between GNU/Linux and Windows
Linux server - Windows client
Sharing via IPP
The preferred way to connect a Windows client to a Linux print server is using IPP. It is a standard printer protocol based on HTTP, allowing you all ways to profit from port forwarding, tunneling etc. The configuration is very easy and this way is less error-prone than using Samba. IPP is natively supported by Windows since Windows 2000.
To configure the server side proceed as described in the section above to enable browsing.
On the Windows computer, go to the printer control panel and choose to 'Add a New Printer'. Next, choose to give a URL. For the URL, type in the location of the printer:
(where host_ip_address is the GNU/Linux server's IP address and printer_name is the name of the printer being connected to, you can also use the server's fully qualified domain name, if it has one, but you may need to set
ServerAlias my_fully_qualified_domain_name in cupsd.conf for this to work).
which will work in a web-browser but not in the add printer dialogue. (At least, not when using cups as an ipp server). The syntax suggested above:
After this, install the native printer drivers for your printer on the Windows computer. If the CUPS server is set up to use its own printer drivers, then you can just select a generic postscript printer for the Windows client(e.g. 'HP Color LaserJet 8500 PS' or 'Xerox DocuTech 135 PS2'). Then test the print setup by printing a test page.
Sharing via Samba
If your client's Windows version is below Windows 2000 or if you experienced troubles with IPP you can also use Samba for sharing. Note of course that with Samba this involves another complex piece of software. This makes this way more difficult to configure and thus sometimes also more error-prone, mostly due to authentication problems.
To configure Samba on the Linux server, edit
/etc/samba/smb.conf file to allow access to printers. File
smb.conf can look something like this:
[global] workgroup=Heroes server string=Arch Linux Print Server security=user [printers] comment=All Printers path=/var/spool/samba browseable=yes # to allow user 'guest account' to print. guest ok=no writable=no printable=yes create mode=0700 write list=@adm root yourusername
That should be enough to share the printer, yet adding an individual printer entry may be desirable:
[ML1250] comment=Samsung ML-1250 Laser Printer printer=ml1250 path=/var/spool/samba printing=cups printable=yes printer admin=@admin root yourusername user client driver=yes # to allow user 'guest account' to print. guest ok=no writable=no write list=@adm root yourusername valid users=@adm root yourusername
Please note that this assumes configuration was made so that users must have a valid account to access the printer. To have a public printer, set guest ok to yes, and remove the valid users line. To add accounts, set up a regular GNU/Linux account and then set up a Samba password on the server. For instance:
# useradd yourusername # smbpasswd -a yourusername
After this, restart the Samba daemon.
Obviously, there are a lot of tweaks and customizations that can be done with setting up a Samba print server, so it is advised to look at the Samba and CUPS documentation for more help. The
smb.conf.example file also has some good samples that might warrant imitating.
Windows server - Linux client
Sharing via LPD
Windows 7 has a built-in LPD server - using it will probably be the easiest approach as it does neither require an installation of Samba on the client nor heavy configuration on the server. It can be activated in the Control Panel under Programs -> Activate Windows functions in the section Print services. The printer must have shared activated in its properties. Use a share name without any special characters like spaces, commas, etc.
Then the printer can be added in CUPS, choosing LPD protocol. The printer address will look like this:
Before adding the printer, you will most likely have to install an appropriate printer driver depending on your printer model. Generic PostScript or RAW drivers might also work.
Sharing via IPP
As above, IPP is also the preferred protocol for printer sharing. However this way might be a bit more difficult than the native Samba approach below, since you need a greater effort to set up an IPP-Server on Windows. The commonly chosen server software is Microsoft's Internet Information Services (IIS).
Sharing via Samba
A much simpler way is using Window's native printer sharing via Samba. There is almost no configuration needed, and all of it can be done from the CUPS Backend. As above noted, if there are any problems the reason is mostly related to authentication trouble and Windows access restrictions.
On the server side enable sharing for your desired printer and ensure that the user on the client machine has the right to access the printer.
The following section describes how to set up the client, assuming that both daemons (cupsd and smbd) are running.
Configuration using the web interface
The Samba CUPS back-end is enabled by default, if for any reason it is not activate it by entering the following command and restarting CUPS.
# ln -s $(which smbspool) /usr/lib/cups/backend/smb
Next, simply log in on the CUPS web interface and choose to add a new printer. As a device choose "Windows Printer via SAMBA".
For the device location, enter:
Or without a password:
Make sure that the user actually has access to the printer on the Windows computer and select the appropriate drivers. If the computer is located on a domain, make sure the user-name includes the domain:
If the network contains many printers you might want to set a preferred printer. To do so use the web interface, go into the printer tab, choose the desired printer and select 'Set as default' from the drop-down list.
For manual configuration stop the CUPS daemon and add your printer to
/etc/cups/printers.conf, which might for example look like this
<DefaultPrinter MyPrinter> AuthInfoRequired username,password Info My printer via SAMBA Location In my Office MakeModel Samsung ML-1250 - CUPS+Gutenprint v5.2.7 # <= use 'lpinfo -m' to list available models DeviceURI smb://username:password@hostname/printer_name # <= server URI as described in previous section State Idle Type 4 Accepting Yes Shared No JobSheets none none QuotaPeriod 0 PageLimit 0 KLimit 0 AllowUser yourusername # <= do not forget to change this OpPolicy default ErrorPolicy stop-printer </Printer>
Then restart the CUPS daemon an try to print a test page.
To set the preferred printer use the following command
# lpoptions -d desired_default_printer_name
See CUPS/Troubleshooting for general troubleshooting tips.
Cannot print with GTK applications
If you get "getting printer information failed" when you try to print from gtk-applications, add this line to your
# serverip some.name.org ServersHostname
Unable to add/modify a printer via SAMBA
When adding a or modifying a printer via SAMBA, the interface hangs at 100% CPU for about 30 seconds and then returns the message
Unable to get list of printer drivers: Success
This is a known bug in Gutenprint (FS#43708). The workaround is to uninstall Gutenprint and install only foomatic-db.
should then return the list of drivers instead of just the "Success" message.
Other operating systems
More information on interfacing CUPS with other printing systems can be found in the CUPS manual, e.g. on http://localhost:631/sam.html#PRINTING_OTHER