Arduino

Related articles

• AVR

Arduino is an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It is intended for artists, designers, hobbyists, and anyone interested in creating interactive objects or environments.

Once hooked up and configured the user may perform read/write tasks over the established serial connection. Examples are interfacing over UART using a serial monitoring program, or programming the microcontroller. Writing, compiling and uploading your code is facilitated by using the official Arduino IDE, which is available in the official repositories. Equally the user may use a compiler and programmer of choice to program the microcontroller.

Installation

• Install either arduino for the original 1.x version of the IDE, arduino-cli for the official CLI or arduino-ide-bin^AUR for the new 2.x release of the IDE. The offline documentation for the 1.x IDE can be installed via arduino-docs.
• Add your user to the uucp user group (more information in the #Accessing serial section).
• You may need to load the cdc_acm module.

Arduino IDE 1.x

The following section only applies to the 1.x version of the IDE. However, it may be possible to adapt some of this for the new IDE.

AVR Boards

To use AVR boards such as the Arduino Uno you can install arduino-avr-core optionally to use Arch Linux upstream avr-gcc instead of the bundled older avr-core. If you still want to use the older arduino-core you need to install it in the board manager. You can always switch between the different cores in the "Tools>Board" menu.

Pinoccio Scout

Pinoccio Scouts can also be programmed using the Arduino IDE. Instructions can be found here. Alternative you can install arduino-pinoccio^AUR.

Intel Galileo

To use the Intel Galileo boards with Arch Linux install the Arduino IDE and download the Galileo tools package via "Tools->Board->Boards Manager". To fix the installation you can follow this github post.

Arduino IDE 1.x or 2.x

These steps should be valid for both versions of the IDE.

AVR Boards

AVR boards are automatically installed by the 2.x release of the IDE however on both the 1.x and 2.x releases the AVR boards can be managed from the boards manager. For 1.x see here.

SparkFun

To use SparkFun boards such as the Pro Micro you need to download their board definitions. More information here and here.

RedBear Duo

You might need to install perl-archive-zip or you will get an error about missing crc32.

Configuration

To interface over USB an interfacing chip is used on the Arduino. Genuine boards boards will typically use an ATmegaxU2, which registers itself as an ACM device. On Linux the cdc_acm module is used. Hence, when connected, the Arduino will show up as /dev/ttyACMx.

Non-genuine Arduino boards typically cheap out on the interfacing chip, typically using one from the Chinese CH34x family. The CH34x does not implement the aforementioned standard and exposes itself as a proprietary UART over USB device. Here the ch341 module is used, making such Arduinos show up as /dev/ttyUSBx. This naming pattern may be customized by altering udev rules.

Note: Remember to keep any serial monitoring programs closed during uploading code in order to free the serial port for the programmer.

Accessing serial

The arduino board communicates with the computer via a serial connection or a serial-over-USB connection, so the user needs read/write access to the serial device file. Udev creates files such as /dev/ttyUSB0 owned by group uucp so adding the user to the uucp group gives the required read/write access. See Users and groups#Group management for details.

Before uploading to the Arduino, be sure to set the correct serial port, board, and processor from the Tools menu in 1.x and the Select board option (located at the top of the IDE) in 2.x.

stty

Preparing:

# stty -F /dev/ttyACM0 cs8 9600 ignbrk -brkint -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke noflsh -ixon -crtscts

Sending commands through Terminal without new line after command

# echo -n "Hello World" > /dev/ttyACM0

Note: As autoreset on serial connection is activated by default on most boards, you need to disable this feature if you want to communicate directly with your board with the last command instead of a terminal emulator (arduino IDE, screen, picocom...). If you have a Leonardo board, you are not concerned by this, because it does not autoreset. If you have an Uno board, connect a 10 µF capacitor between the RESET and GND pins. If you have another board, connect a 120 ohms resistor between the RESET and 5V pins. See https://playground.arduino.cc/Main/DisablingAutoResetOnSerialConnection for more details.

Reading what your Arduino has to tell you:

$ cat /dev/ttyACM0

Arduino-Builder

You can also build Arduino sketches with the arduino-builder command line tool. In order to use the provided arduino-avr-core with upstream avr-gcc and avrdude you need to create a small settings file:

build.options.json

{
    "fqbn": "archlinux-arduino:avr:uno",
    "hardwareFolders": "/usr/share/arduino/hardware",
    "toolsFolders": "/usr/bin"
}

Compile a sketch with:

$ arduino-builder -build-options-file build.options.json blink.ino

Or pass all options via command line:

$ arduino-builder -fqbn archlinux-arduino:avr:uno -hardware /usr/share/arduino/hardware -tools /usr/bin blink.ino

Alternatives to the IDE

ArduIDE

ArduIDE is a Qt-based IDE for Arduino, available with arduide-git^AUR.

Arduino-CMake

Using Arduino-CMake-Toolchain and CMake you can build Arduino firmware from the command line using multiple build systems. CMake lets you generate the build system that fits your needs, using the tools you like. It can generate any type of build system, from simple Makefiles, to complete projects for Eclipse, Visual Studio, XCode, etc.

Requirements: cmake, arduino, avr-gcc, avr-binutils, avr-libc, avrdude.

Makefile

Instead of using the Arduino IDE it is possible to use another editor and a Makefile.

Set up a directory to program your Arduino and copy the Makefile into this directory. A copy of the Makefile can be obtained from this GitHub template You will have to modify this a little bit to reflect your settings. The makefile should be pretty self explanatory. Here are some lines you may have to edit.

PORT = usually /dev/ttyUSBx, where x is the usb serial port your arduino is plugged into
TARGET = your sketch's name
ARDUINO = /usr/share/arduino/lib/targets/arduino

Depending on which library functions you call in your sketch, you may need to compile parts of the library. To do that you need to edit your SRC and CXXSRC to include the required libraries.

Now you should be able to make && make upload to your board to execute your sketch.

Arduino-mk

arduino-mk^AUR is another alternative Makefile approach. It allows users to have a local Makefile that includes Arduino.mk. See project page for usage.

For Arduino 1.5, try the following local Makefile (because Arduino 1.5's library directory structure is slightly different):

ARDUINO_DIR = /usr/share/arduino
ARDMK_DIR = /usr/share/arduino
AVR_TOOLS_DIR = /usr
AVRDUDE_CONF = /etc/avrdude.conf
ARDUINO_CORE_PATH = /usr/share/arduino/hardware/archlinux-arduino/avr/cores/arduino
ARDUINO_PLATFORM_LIB_PATH = /usr/share/arduino/hardware/archlinux-arduino/avr/libraries
BOARDS_TXT = /usr/share/arduino/hardware/archlinux-arduino/avr/boards.txt
ARDUINO_VAR_PATH = /usr/share/arduino/hardware/archlinux-arduino/avr/variants
BOOTLOADER_PARENT = /usr/share/arduino/hardware/archlinux-arduino/avr/bootloaders


BOARD_TAG    = uno
ARDUINO_LIBS =

include /usr/share/arduino/Arduino.mk

In some cases you could need to install avr-libc and avrdude.

Scons

Using scons together with arscons it is very easy to use to compile and upload Arduino projects from the command line. Scons is based on python and you will need python-pyserial to use the serial interface. Install python-pyserial and scons.

That will get the dependencies you need too. You will also need Arduino itself so install it as described above. Create project directory (eg. test), then create a arduino project file in your new directory. Use the same name as the directory and add .ino (eg. test.ino). Get the SConstruct script from arscons and put it in your directory. Have a peek in it and, if necessary, edit it. It is a python script. Edit your project as you please, then run

$ scons                # This will build the project
$ scons upload         # This will upload the project to your Arduino

PlatformIO

PlatformIO is a python tool to build and upload sketches for multiple Hardware Platforms, at the moment of writing these are Arduino/AVR based boards, TI MSP430 and TI TM4C12x Boards. In the near future the author plans to add a library function that allows to search and include libraries directly from GitHub.

Installation

Install the platformio^AUR or platformio-git^AUR package.

Usage

$ platformio platform install atmelavr
$ platformio init

Create platformio.ini:

platformio.ini

#
# Atmel AVR based board + Arduino Wiring Framework
#
[env:ArduinoMega2560]
platform = atmelavr
framework = arduino
board = megaatmega2560   
upload_port = /dev/ttyACM0 
targets = upload

$ platformio run

Emacs

It is possible to configure Emacs as IDE.

Install the package emacs-arduino-mode-git^AUR in order to enable the arduino-mode in emacs.

Add to the init script:

~/.emacs

;; arduino-mode
(require 'cl)
(autoload 'arduino-mode "arduino-mode" "Arduino editing mode." t)
(add-to-list 'auto-mode-alist '("\.ino$" . arduino-mode))

You can compile and upload the sketches using Arduino-mk (see above) with M-x compile make upload.

Main resource: here.

Troubleshooting

Consistent naming of Arduino devices

If you have more than one Arduino you may have noticed that they names /dev/ttyUSB[0-9] are assigned in the order of connection. In the IDE this is not so much of a problem, but when you have programmed your own software to communicate with an Arduino project in the background this can be annoying. Use the following udev rules to assign static symlinks to your Arduino's:

/etc/udev/rules.d/52-arduino.rules

SUBSYSTEMS=="usb", KERNEL=="ttyUSB[0-9]*", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", SYMLINK+="sensors/ftdi_%s{serial}"

Your Arduino's will be available under names like /dev/sensors/ftdi_A700dzaF. If you want you can also assign more meaningfull names to several devices like this:

/etc/udev/rules.d/52-arduino.rules

SUBSYSTEMS=="usb", KERNEL=="ttyUSB[0-9]*", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", ATTRS{serial}=="A700dzaF", SYMLINK+="arduino/nano"

which will create a symlink in /dev/arduino/nano to the device with the specified serialnumber. You do need to unplug and replug your Arduino for this to take effect or run

# udevadm trigger

Common idVendor/idProduct pairs can be found in /usr/share/arduino/hardware/archlinux-arduino/avr/boards.txt in the distribution package. Note that some of them (notably FTDI ones) are not unique to the Arduino platform. Using serial attribute is a good way to distinguish between various devices.

Error opening serial port

You may see the serial port initially when the IDE starts, but the TX/RX leds do nothing when uploading. You may have previously changed the baudrate in the serial monitor to something it does not like. Edit ~/.arduino/preferences.txt so that serial.debug_rate is a different speed, like 115200.

Working with Uno/Mega2560

The Arduino Uno and Mega2560 have an onboard USB interface (an Atmel 8U2) that accepts serial data, so they are accessed through /dev/ttyACM0 created by the cdc-acm kernel module when it is plugged in.

The 8U2 firmware may need an update to ease serial communications. See [1] for more details and reply #11 for a fix. The original arduino bbs, where you can find an image explaining how to get your Uno into DFU, is now in a read-only state. If you do not have an account to view the image, see [2].

You can perform a general function test of the Uno by putting it in loopback mode and typing characters into the arduino serial monitor at 115200 baud. It should echo the characters back to you. To put it in loopback, short pins 0 -> 1 on the digital side and either hold the reset button or short the GND -> RESET pins while you type.

Not recognizing USB port with Mega2560 cheap Chinese clones

Try installing its driver: i2c-ch341-dkms^AUR.

1.x Application not resizing with WM, menus immediately closing

see Java#Gray window, applications not resizing with WM, menus immediately closing

Fails to upload: programmer is not responding

Changing processor setting from ATmega328P to ATmega328P (Old Bootloader) (See Tools->Processor in Arduino IDE) may help with upload failures.

1.x Crashing with java.lang.NullPointerException after a fresh install

You need to install arduino-avr-core.

Serial port conflict with brltty

If the serial port for the arduino is not visible at /dev/ttyUSB*, and dmesg outputs the following when the device is connected:

[  210.327434] usb 3-1: usbfs: interface 0 claimed by ch341 while 'brltty' sets config #1
[  210.327884] ch341-uart ttyUSB0: ch341-uart converter now disconnected from ttyUSB0

Then you may need to uninstall the brltty package. See [3] for more details.

Failure to upload with Nano RP2040 Connect

If your upload fails with

Failed uploading: uploading error: exit status 1

Try running the following script to setup Raspberry Pi RP2040 bootloader mode udev rules.

# ~/.arduino15/packages/arduino/hardware/mbed_nano/3.5.1/post_install.sh

See also

• Official website
• IDE v2 Getting Started Guide
• https://answers.ros.org/question/9097/how-can-i-get-a-unique-device-path-for-my-arduinoftdi-device/