USB 3G Modem

From ArchWiki
(Redirected from Gcom)
Jump to: navigation, search

Tango-edit-clear.pngThis article or section needs language, wiki syntax or style improvements.Tango-edit-clear.png

Reason: does not conform to Help:Style (Discuss in Talk:USB 3G Modem#)

A number of mobile telephone networks around the world offer mobile internet connections over UMTS (or EDGE or GSM) using a portable USB modem device.

Remove the PIN

First of all use your SIM card in a normal phone and disable the PIN request if present. If the SIM card asks the PIN wvdial will not work.

Failing that, you can also use mmcli to unlock the SIM card:

# mmcli -i SIMNUMBER --pin=XXXX

where SIMNUMBER can be found using mmcli -L and mmcli -m X.

Device identification

Examine the output of

$ lsusb

which will show the vendor and product IDs of the device. Note that some devices will show two different product IDs at different times as explained below.

Mode switching

Often these devices will have two modes (1) USB flash memory storage (2) USB Modem. The first mode, sometimes known as ZeroCD, is often used to deliver an internet communications program for another operating system and is generally of no interest to Linux users. Additionally some have a slot into which the user can insert an additional flash memory card.

A useful utility for switching these devices into modem mode is usb_modeswitch, available in the official repositories.

Udev rules are supplied with the package in /lib/udev/rules.d/40-usb_modeswitch.rules. This contains entries for many devices, which it will switch to modem mode upon insertion.

When a device is switched, its product ID may change to a different value. The vendor ID will remain unchanged. This can be seen in the output of lsusb.

Some devices are supported in the USB serial kernel module called "option" (after the Option devices, but not limited to just those) and may be used without usb_modeswitch.

Udev itself included a utility called /lib/udev/modem-modeswitch. In udev 157 this was renamed to /lib/udev/mobile-action-modeswitch and morphed into a tool that only switches Mobile Action cables. For other devices use usb_modeswitch.

Note: You can find an alternative way to do this base on eject command here.

Connection

Network Manager

After installing usbutils and usb_modeswitch, you just need to install modemmanager to make the modem work with NetworkManager.

Make sure both NetworkManager and ModemManager services are running, see systemd#Using units for details.

Make sure mobile-broadband-provider-info and nm-connection-editor are installed.

A system restart might be necessary for ModemManager to detect the USB modem. After you restart the NetworkManager-applet and plug the modem in again NetworkManager should recognize the modem in the menu without further configuration. Setting up the modem in NetworkManager is self-explanatory, you should only need the login-information provided by your network provider.

Whilst running ModemManager gammu will not work. SMS and Ussd codes can be still used with modem-manager-gui.

wvdial

See main article: wvdial

netctl

Netctl can be used to establish a connection using a USB modem. An example configuration file provided by netctl is located at /etc/netctl/examples/mobile_ppp.

See the netctl article for more information.

sakis3g

There may be the chance that the modem stick is supported by sakis3g which is an all in one command line script and automates all the steps above. Install sakis3gAUR from the AUR.

Low connection speed

Someone claims that the connection speed under Linux is lower than Windows: [1]

A short summary for possible solutions which are not fully verified. In most of conditions, the low speed is caused by bad receiver signals and too many people in cell. But you still could use the following method to try to improve the connection speed.

QoS parameter

The AT+CGEQMIN and AT+CGEQREQ commands can be used to set the QoS. It is also possible to decrease and limit the connect speed. Add the following Init command in /etc/wvdial.conf:

Init6 = AT+CGEQMIN=1,4,64,640,64,640
Init7 = AT+CGEQREQ=1,4,64,640,64,640

Baud parameter

Baud parameter in wvdial.conf could be used to increase the connection speed.

Baud = 460800

But the official Huawei E261 windows application set the Baud=9600 under Windows Vista. More verifications are needed to double check this point.

Monitor used bandwith

Frequently a 3G connection obtained via a mobile phone operator comes with restricted bandwidth, so that you are only allowed to use a certain bandwidth per time (e.g. 1GB per month). While it is quite straight-forward to know which type of network applications are pretty bandwidth extensive (e.g. video streaming, gaming, torrent, etc.), it may be difficult to keep an overview about overall consumed bandwidth.

A number of tools are available to help with that. Two console tools are vnstat, which allows to keep track of bandwith over time, and iftop to monitor bandwidth of individual sessions. If you are a KDE user, knemo might help. All are available in the official repositories.

Reading SMS

This was tested on a Huawei EM770W (GTM382E) 3g card integrated into an Acer Aspire AS3810TG laptop.

$ pacman -S gnokii
$ mkdir -p $XDG_CONFIG_HOME/gnokii

Usually the configuration directory is ~/.config/gnokii.

$ cp /etc/gnokiirc ~/.config/gnokii/config

edit ~/.config/gnokii/config as follows:

port = /dev/ttyUSB0

You may have to use a different port depending on your configuration, for example /dev/ttyUSB1 or something else:

model = AT
connection = serial

You need to be part of the uucp group to use /dev/ttyUSB0, for example if your user is called "x":

# gpasswd -a x uucp
$ newgrp uucp

The newgrp command allows you to take advantage of the new group assignment immediately without having to logout/login.

Then launch gnokii:

$ xgnokii

Click on the "SMS" icon button, a window opens up. Then click: "messages->activate sms reading". Your messages will show up in the window.

command line script

A small command line script using gnokii to read SMS on your SIM card (not phone memory) without having to start a GUI:

$  gnokii --getsms SM 0 end 2>&1|grep Text -A1 -B3|grep -v Text

What it does:

gnokii # invoke gnokii
--getsms SM 0 end # read SMS from SM-memory location (=SIM card) starting at 0 and reading all occupied memory locations ("end")
2>&1 # connect STDERR to STDOUT to make sure the output from the --getsms command can be piped to grep
|grep Text # pipe output from gnokii to grep, anchoring at output containing "Text"
-A1 -B3 # print one line after the matched pattern and three lines before the matched pattern
|grep -v Text # grep result to another grep to exclude the "Text" line (-v for inverting the pattern)

Granted this does not work very well if your SMS contains the word "Text", but you may adapt the script to your liking.

Fix image quality

If you are getting low quality images while browsing the web over a mobile broadband connection with the hints "shift+r improves the quality of this image" and "shift+a improves the quality of all images on this page", follow these instructions:

Install tinyproxy, available in the official repositories.

Edit /etc/tinyproxy/tinyproxy.conf and insert the following two lines:

AddHeader "Pragma" "No-Cache"
AddHeader "Cache-Control" "No-Cache"

Start tinyproxy:

systemctl start tinyproxy

Configure your browser to use localhost:8888 as a proxy server and you are all done. This is especially useful if you are using, for example, Google Chrome which, unlike Firefox, does not allow you to modify the Pragma and Cache-Control headers.